I did quite a lot of research looking for places that will inlet Model 54 and 64 Anschutz actions. Some inlet 54, others 64 and a very few do both. Here is the list I have come up with so far. I will add more once I have located them. Hopefully this will become a sticky so others don't have to do as much hunting for this information.
The below makers all make one or the other of, left shooter, right action, left shooter, left action and right hand versions.
Last Edited Feb 24, 2024
Stock Interchangeability information
1710, 1712, 1720 and 1730 interchange
From Camster - Dean, all 1700 series stocks will interchange,provided that they are for the same style of safety and the same barrel contour. Standard barrel channels will need to be opened up for heavy barrels. Some early side safety guns use the same basic stock pattern as the earlier wing safety stocks, so they will work with wing safety action stocks. Later side safety stocks will not work with the wing safety action stocks unless a channel is cut on the right side to accommodate the side safety mechanism.
1727 22 RF and the 1827 Biathlon and 1927 fast fire stocks interchange. You can also put the action in any 1900 single shot stock but the magazine well and front recoil lug (1727 action only) will need to be inlet and the stock adjusted for the Fortner bolt and safety.
The 54.18 and the 54.18 MSR will fit into any 1900 series stock as long as you inlet the magazine for the MSR.
1700 Match 54 Repeater vs. Match 54 Single Shot ( 1900 Series) Action Design From Anschutz Site Technical Questions
We get this question a lot about if a 1700 series will fit in a Match 54 stock from a 1900 series, or if a 1900 series can be fit into a 1710 or 1712 stock. The short answer is no; they are different.
With both actions stripped of triggers, they give the initial impression that you can. They are very similar in length and the same OD, but there are two very critical details which prevent this.
To help show this, here are a few photos below. The screws threaded into the action show where the action screws are located.
The 5018 trigger mounted on the 1913 sits much further back on the action, very close to the end of the tang. To fit this in a Sporter stock ( 1700 series ) requires considerable wood removal. Most Sporter stocks will not allow this and become too weak in that area.
This may also help the question about swapping triggers between these models; it cannot be done. The photos below show why.
Will an 1807 barreled action fit a 1413 or 1411 stock?
From Thomasconnor You'll have to inlet for the trigger. A bit to the rear and a lot for the side safety, which if removed requires much less work. The lower stock below has been inlet for 18XX and 19XX actions...Tom
Inletting for a 54.18 MSR
Bottom
Top view
All model 64 repeaters prior to 2009 interchange. All single shot 64 actions interchange before 2009. You can tell the larger 26MM action predominantely by the largge black plastic bolt handle and scallops on the top of the action. You can Devcon the larger stock to accept the smaller, earlier 64 action.
After 2009 the action is slightly larger in diameter, 26mm. 1415/1417/1516/1617 and MPR all interchange with exception of barrel diameter.
Model 64 R Benchrest
Stock Maker information
ANSCHÜTZ North America - Now Has A Custom shop operation that also does Stocks. Not cheap but very nice work. They do not take customer orders, rifles must be factory new when they enter the Custom shop and are then bought by a customer.
Stocks
XLR Element 4.0 Chassis, TR-2 Buttstock & Ergo Tactical Grip
Update Feb 2020 XLR Chassis stocks available as stock only form Anschutz
54 Action Stocks
XLR Element 4.0 - Stock Only
SKU: XLR.GEN41700
US$695.00
Anschutz Custom XLR Element 4.0 for 1710 or 1712 models
Chassis Features:
Machined from solid 6061 T-6 billet aluminum
MLOK™ attachment points down both sides of forearm
Tactical-Lite Buttstock
RRS (Really Right Stuff) Spec 1.5" Dovetail (Arca-Swiss) forearm
Anschutz 10-5/8 inch Rail at 6 o'clock position of forend
Multi-point radial cut inlet eliminates the need for traditional V-Block or Glass Bedding
Adjustable LOP: 12" to 15"
Adjustable Butt-Plate Height 1.575"
Adjustable Cheek Piece Height & 10 degree cant
Built in bubble level - New on the 4.0 version
User inter-changeable pistol grip
Weight of chassis with action screws 3 lbs 7.5oz
GSI Building
7661 Commerce LN
Trussville, AL 35173-2837
Phone: 205-655-7500, and 205-655-7502
Sales: sales@anschutznorthamerica.com
General Information: info@anschutznorthamerica.com
Service & Repairs: service@anschutznorthamerica.com
Baer Custom Rifles - Make a large selection of Target stocks and some REALLY cool all aluminum ones.
http://www.baercustomrifles.com/
Boyd's Rifle Stock - So far only for the Anschutz 64 action in right hand. Feb 2024 still just 64 rh action
Brown Precisison
http://www.brownprecision.com/brown-precision-stocks.htm
Kelby Stocks - makes 54 BR and other styles.
http://www.kelbly.com/stocks-kelbly-brfb-hcfb.html
McMillan Rifle Stocks
Macmillan Stocks - MCMFamily.com
Don Stith
St. Louis Plains Rifle Co. - Don Stith
Unfortunately Don Passed in July 2022. Marks is still carving stocks like he did for 25 years for Don but you have to inlet the trigger and finish the stock, which is the part Don used to do.
Mark Weader
Jack's Mountain Stock Co.
101 Cave Lane
McClure, PA 17841
Shop #717-543-5370
carve4utwo@gmail.com
Great American Gunstock Company
Great American Gunstock Company
Aug 2015 Update The Great American Gunstock Co. is no longer manufacturing gunstocks.
We have a limited inventory of stocks which we are selling at reduced prices and you can reach us at the following number:
(530) 632-9834
Henry L. Pohl
Most of the assets--machinery, patterns, tooling, etc. have been purchased by...
Walnut Grove Gunstocks
711 Hale Rd.
Weiser, Idaho 83673
(208) 549-1323
You can contact them about your custom gunstock needs....
Richards Microfit - The Actions are not listed but they do them if you talk to them.
Richards Microfit Gunstocks
Master Class Stocks (814) 742-7868.
MASTER CLASS Stocks and Shooting Accessories, Inc.
MPI Gunstocks
http://www.mpistocks.com/index.htm
Shehane Tracker Stocks
Target Stocks - Nightforce scopes & Shehane Tracker Stocks - Custom Rifle Stocks
Canyon Creek - Expensive but truly beautiful Custom Walnut stocks
Canyon Creek Gun Stock
Thanks to NMC EXP - Another custom rifle builder and stock maker for your list is:
Doan Trevor Doan Trevor Custom Rifle Building
Staffordshire Synthetic Stocks - England Staffordshire Synthetic Stocks
TM Stock Works Stockwork, solvent, oil & grease
From Bronco - Just got back from the 2017 shot Show where I found MDT, mdttac.com that makes chassis for 54 and 64 actions. Uses AR stock and pistol grip. LSS-22 chassis also made for Ruger American, Browning T-bolt, CZ 455, and Savage Mark II. Have one on order for a 1710 DHB, will report when I've had a chance to test it out.
Modular Driven Technologies MDT Chassis Systems, Magazines & Accessories for Precision Rifles Cost of Chassis $400. No evidence of Left hand for 54 or 64 actions so a call may be necessary.
Manners Composit Stocks - MCS https://mannersstocks.com/catalogsearch/result/?q=anschutz+64+action
Many choices of stock for the 54 and 64 action.
We are currently in contract with Anschutz so we are unable to sell to the public, but if you would like one you can order directly through Anschutz North America. Thank you
Taelor
1232 Swift Ave | Kansas City MO 64116
816.283.3334 | sales@mannersstocks.com
www.mannersstocks.com
Added May 2017
Gunville Stocks Gunville.com || Hand Made Quality Reproduction Gun Stocks. Made in USA Will Duplicate your stock and provides inletted stocks for 54 and 64 actions. Added May 2017
MCRS Tactical CNC made stocks.http://www.mcrstactical.com 403-401-1313. They currently do Biathlon stocks for most 22s, Will produce stocks in wood (Walnut, Cherry, Maple), or composite. They make a wide selection of F-class, BR, Hunting and Tactical stocks. Their prices are Canadian so you save 35%, They will assist in filling out the BTF Import form at no charge.
Zorrow Stock Maker
Custom Stocks in 54 and 64 actions. Excels in bench rest configurations but will do all requests.
The picture of the Model 64R benchrest above is one of his.
Email = res04iay@frontier.com
Phone = 425-344-1602
Carl Bernosky http://www.carlbernosky.com.
Wenig Custom Gunstocks
http://www.wenig.com/
PSE Composits Ireland
http://www.pse-composites.com/
McRee Precision
https://shop.mcreesprecision.net/G10...-COMP-AN64.htm
PHONE 662-453-0022, TECH/INFO-EMAIL contact@mcreesprecision.net
GRS Rifle Stocks. Make quite a few models and different inlets
https://www.grsriflestocks.com/rifle-stocks
MDT Tactical Chassis add Feb 2020
https://mdttac.ca/lss-chassis-system/
The below makers all make one or the other of, left shooter, right action, left shooter, left action and right hand versions.
Last Edited Feb 24, 2024
Stock Interchangeability information
1710, 1712, 1720 and 1730 interchange
From Camster - Dean, all 1700 series stocks will interchange,provided that they are for the same style of safety and the same barrel contour. Standard barrel channels will need to be opened up for heavy barrels. Some early side safety guns use the same basic stock pattern as the earlier wing safety stocks, so they will work with wing safety action stocks. Later side safety stocks will not work with the wing safety action stocks unless a channel is cut on the right side to accommodate the side safety mechanism.
1727 22 RF and the 1827 Biathlon and 1927 fast fire stocks interchange. You can also put the action in any 1900 single shot stock but the magazine well and front recoil lug (1727 action only) will need to be inlet and the stock adjusted for the Fortner bolt and safety.
The 54.18 and the 54.18 MSR will fit into any 1900 series stock as long as you inlet the magazine for the MSR.
1700 Match 54 Repeater vs. Match 54 Single Shot ( 1900 Series) Action Design From Anschutz Site Technical Questions
We get this question a lot about if a 1700 series will fit in a Match 54 stock from a 1900 series, or if a 1900 series can be fit into a 1710 or 1712 stock. The short answer is no; they are different.
With both actions stripped of triggers, they give the initial impression that you can. They are very similar in length and the same OD, but there are two very critical details which prevent this.
To help show this, here are a few photos below. The screws threaded into the action show where the action screws are located.
The 5018 trigger mounted on the 1913 sits much further back on the action, very close to the end of the tang. To fit this in a Sporter stock ( 1700 series ) requires considerable wood removal. Most Sporter stocks will not allow this and become too weak in that area.
Technical Questions
Technical Questions We have recently added this new section in to help address some of the more common questions we receive about of products. Please scroll down the page to see if your question...
www.anschutznorthamerica.com
This may also help the question about swapping triggers between these models; it cannot be done. The photos below show why.
Will an 1807 barreled action fit a 1413 or 1411 stock?
From Thomasconnor You'll have to inlet for the trigger. A bit to the rear and a lot for the side safety, which if removed requires much less work. The lower stock below has been inlet for 18XX and 19XX actions...Tom
Inletting for a 54.18 MSR
Bottom
Top view
All model 64 repeaters prior to 2009 interchange. All single shot 64 actions interchange before 2009. You can tell the larger 26MM action predominantely by the largge black plastic bolt handle and scallops on the top of the action. You can Devcon the larger stock to accept the smaller, earlier 64 action.
After 2009 the action is slightly larger in diameter, 26mm. 1415/1417/1516/1617 and MPR all interchange with exception of barrel diameter.
2010 - Anschutz Hunting Catalogue.pdf
drive.google.com
Model 64 R Benchrest
Stock Maker information
ANSCHÜTZ North America - Now Has A Custom shop operation that also does Stocks. Not cheap but very nice work. They do not take customer orders, rifles must be factory new when they enter the Custom shop and are then bought by a customer.
Stocks
XLR Element 4.0 Chassis, TR-2 Buttstock & Ergo Tactical Grip
Update Feb 2020 XLR Chassis stocks available as stock only form Anschutz
54 Action Stocks
XLR Element 4.0 - Stock Only
SKU: XLR.GEN41700
US$695.00
Anschutz Custom XLR Element 4.0 for 1710 or 1712 models
Chassis Features:
Machined from solid 6061 T-6 billet aluminum
MLOK™ attachment points down both sides of forearm
Tactical-Lite Buttstock
RRS (Really Right Stuff) Spec 1.5" Dovetail (Arca-Swiss) forearm
Anschutz 10-5/8 inch Rail at 6 o'clock position of forend
Multi-point radial cut inlet eliminates the need for traditional V-Block or Glass Bedding
Adjustable LOP: 12" to 15"
Adjustable Butt-Plate Height 1.575"
Adjustable Cheek Piece Height & 10 degree cant
Built in bubble level - New on the 4.0 version
User inter-changeable pistol grip
Weight of chassis with action screws 3 lbs 7.5oz
GSI Building
7661 Commerce LN
Trussville, AL 35173-2837
Phone: 205-655-7500, and 205-655-7502
Sales: sales@anschutznorthamerica.com
General Information: info@anschutznorthamerica.com
Service & Repairs: service@anschutznorthamerica.com
Baer Custom Rifles - Make a large selection of Target stocks and some REALLY cool all aluminum ones.
http://www.baercustomrifles.com/
Boyd's Rifle Stock - So far only for the Anschutz 64 action in right hand. Feb 2024 still just 64 rh action
Hardwood Gunstock Manufacturer | Boyds Hardwood Gunstocks
Boyds uses top-grade hardwood to craft durable, long-lasting shotgun & rifle stocks for top-selling firearm brands, including custom options. Get yours today!
www.boydsgunstocks.com
Brown Precisison
http://www.brownprecision.com/brown-precision-stocks.htm
Kelby Stocks - makes 54 BR and other styles.
http://www.kelbly.com/stocks-kelbly-brfb-hcfb.html
McMillan Rifle Stocks
Macmillan Stocks - MCMFamily.com
Don Stith
St. Louis Plains Rifle Co. - Don Stith
Unfortunately Don Passed in July 2022. Marks is still carving stocks like he did for 25 years for Don but you have to inlet the trigger and finish the stock, which is the part Don used to do.
Mark Weader
Jack's Mountain Stock Co.
101 Cave Lane
McClure, PA 17841
Shop #717-543-5370
carve4utwo@gmail.com
Great American Gunstock Company
Great American Gunstock Company
Aug 2015 Update The Great American Gunstock Co. is no longer manufacturing gunstocks.
We have a limited inventory of stocks which we are selling at reduced prices and you can reach us at the following number:
(530) 632-9834
Henry L. Pohl
Most of the assets--machinery, patterns, tooling, etc. have been purchased by...
Walnut Grove Gunstocks
711 Hale Rd.
Weiser, Idaho 83673
(208) 549-1323
You can contact them about your custom gunstock needs....
Richards Microfit - The Actions are not listed but they do them if you talk to them.
Richards Microfit Gunstocks
Master Class Stocks (814) 742-7868.
MASTER CLASS Stocks and Shooting Accessories, Inc.
MPI Gunstocks
http://www.mpistocks.com/index.htm
Shehane Tracker Stocks
Target Stocks - Nightforce scopes & Shehane Tracker Stocks - Custom Rifle Stocks
Canyon Creek - Expensive but truly beautiful Custom Walnut stocks
Canyon Creek Gun Stock
Thanks to NMC EXP - Another custom rifle builder and stock maker for your list is:
Doan Trevor Doan Trevor Custom Rifle Building
Staffordshire Synthetic Stocks - England Staffordshire Synthetic Stocks
TM Stock Works Stockwork, solvent, oil & grease
From Bronco - Just got back from the 2017 shot Show where I found MDT, mdttac.com that makes chassis for 54 and 64 actions. Uses AR stock and pistol grip. LSS-22 chassis also made for Ruger American, Browning T-bolt, CZ 455, and Savage Mark II. Have one on order for a 1710 DHB, will report when I've had a chance to test it out.
Modular Driven Technologies MDT Chassis Systems, Magazines & Accessories for Precision Rifles Cost of Chassis $400. No evidence of Left hand for 54 or 64 actions so a call may be necessary.
Manners Composit Stocks - MCS https://mannersstocks.com/catalogsearch/result/?q=anschutz+64+action
Many choices of stock for the 54 and 64 action.
We are currently in contract with Anschutz so we are unable to sell to the public, but if you would like one you can order directly through Anschutz North America. Thank you
Taelor
1232 Swift Ave | Kansas City MO 64116
816.283.3334 | sales@mannersstocks.com
www.mannersstocks.com
Added May 2017
Gunville Stocks Gunville.com || Hand Made Quality Reproduction Gun Stocks. Made in USA Will Duplicate your stock and provides inletted stocks for 54 and 64 actions. Added May 2017
MCRS Tactical CNC made stocks.http://www.mcrstactical.com 403-401-1313. They currently do Biathlon stocks for most 22s, Will produce stocks in wood (Walnut, Cherry, Maple), or composite. They make a wide selection of F-class, BR, Hunting and Tactical stocks. Their prices are Canadian so you save 35%, They will assist in filling out the BTF Import form at no charge.
Zorrow Stock Maker
Custom Stocks in 54 and 64 actions. Excels in bench rest configurations but will do all requests.
The picture of the Model 64R benchrest above is one of his.
Email = res04iay@frontier.com
Phone = 425-344-1602
Carl Bernosky http://www.carlbernosky.com.
Wenig Custom Gunstocks
http://www.wenig.com/
PSE Composits Ireland
http://www.pse-composites.com/
McRee Precision
https://shop.mcreesprecision.net/G10...-COMP-AN64.htm
PHONE 662-453-0022, TECH/INFO-EMAIL contact@mcreesprecision.net
GRS Rifle Stocks. Make quite a few models and different inlets
https://www.grsriflestocks.com/rifle-stocks
MDT Tactical Chassis add Feb 2020
https://mdttac.ca/lss-chassis-system/