Fixing Loose Ejectors - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > > >

Notices

Join Team RFC to remove these ads.
 
 
Thread Tools Display Modes
  #1  
Old 05-12-2017, 10:04 AM
Test_Engineer

Join Date: 
Nov 2014
Location: 
On a Colorado glacier
Posts: 
2,972
TPC Rating: 
0% (0)
Fixing Loose Ejectors



Log in to see fewer ads
The ejector on my MKII was loose rotationally, but was still tight up and down. If it was loose up/down, I'd have sent it back to Ruger to fix.

I'm posting my fix here in the MKIV forum because the ejector and rivet really hasn't changed from the first RST/MKI models to the current MKIVs.

The ejector is riveted to the bottom of the receiver with a tab on the back of the ejector sitting in a notch on the receiver. With my receiver turned upside down, the ejector is straight when the tab is all the way to the left in the notch. This leaves a small gap on the right. So I wondered if some of the receiver material could be drifted into the gap to hold the ejector straight.

I grabbed a center punch and put the muzzle down on a hardwood block (my vice is not padded). It's important to not punch too close to the gap, or it can slide in and push material out - making the gap bigger. I started a little less then 1/16" away and gave it a wap. This was a little too far away. So I moved down a little and cut the distance in half.

This hit was a BULLSEYE! The gap was filled nicely and my ejector is straight and rock solid! Only took about 10 minutes to get it fixed. Here's a picture with a green arrow added to the fix:



I hope this helps.
  #2  
Old 05-17-2017, 07:47 PM
valvestem's Avatar
valvestem
US Coast Guard Veteran Law Enforcement Officer NRA Member - Click Here To Join!

Join Date: 
Apr 2016
Location: 
Maine
Posts: 
186
TPC Rating: 
0% (0)
This should be a "sticky" for future reference just in case someone has the same issue someday. Thank you for the post.
  #3  
Old 06-01-2017, 02:33 AM
Test_Engineer

Join Date: 
Nov 2014
Location: 
On a Colorado glacier
Posts: 
2,972
TPC Rating: 
0% (0)
There's much HOGWASH in the previous post.

First, the tab on the back of the ejector is NOT for "alignment purposes". It's a stop designed to prevent the ejector arm from rotating too far outward. It only functions correctly when it's against the left side of the notch, as oriented in post #1. The tab does NOT belong in the "middle of the cut-out".

Apparently, someone at Ruger thought the tab could be anywhere in the notch when they made my MKII. The tab was against the right side instead of the left. The rivet was very nicely staked, and was tight. But it left the ejector misaligned, resulting in the bolt grinding on the ejector with every cycle. See how bad it wore as a result:



It was the act of turning the ejector straight that left the rivet's hold a bit loose.

Next, squashing the (fairly soft) rivet is NOT a "better fix" than drifting the (very hard) receiver material into the notch. If you want to see a "Red Green duct tape job that probably won't last very long", you need look no further than the second photo in the previous post. WOW, is that an ugly fix!

Lastly, because of the stop, it's simply not possible for "the ejector tip to end up too far to the left". That is, unless the ejector arm gets bent while someone tries to pound the rivet with some crappy kind of holding jig.

So if you don't want to send your pistol back to Ruger, or build a quality jig to tighten only a single rivet - the center punch option is fast, easy, and reliable. Here's my nice and straight, tight ejector:

Sponsored Links
Advertisement
 
  #4  
Old 06-01-2017, 10:18 AM
Sophia's Avatar
Sophia

That Evil Admin Lady
Join Date: 
Dec 2006
Location: 
Raggedy Edge of the 'Verse
Posts: 
22,535
TPC Rating: 
100% (23)
If you men are going to continue this conversation please do so without making personal insults. If you men cannot discuss things without insulting each other I invite you to put each other on your ignore lists, otherwise I implore you to act like adults.

Starting the food fight with an insult then reporting a post that responds to it isn't going to score any points.
__________________
Nobody But Me
  #5  
Old 06-10-2017, 03:56 PM
gunsmither
RFC Sponsor
NRA Member - Click Here To Join! GOA Member

RFC Sponsor
Join Date: 
May 2002
Location: 
The TAX FARM known as Wa. State!
Posts: 
944
TPC Rating: 
0% (0)
Did Ruger do this?



Is this really a Ruger Factory repair? Pretty nasty looking!
Somebody beat the dog snot out of it!

If I had sent this gun back to Ruger, and it came back looking like this photo,
I would be very reluctant to give it back to a customer in that condition,
nor would I post a photo of it, citing it as a proper repair.

That is a very poor excuse for a "repair". I have tightened a few ejectors
by tightening the rivet, but they sure never looked like this mess.
__________________
http://www.gunsmithertools.com

UNIQUE gunsmithing tools and accessories for 10/22's, MkII's, S&W

Last edited by gunsmither; 06-11-2017 at 08:47 PM. Reason: Added info
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off




All times are GMT -5. The time now is 03:56 PM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x