592m - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > >

Notices

Join Team RFC to remove these ads.
Reply
 
Thread Tools Display Modes
  #1  
Old 01-27-2019, 06:28 PM
Balvar24
NRA Member - Click Here To Join!

Join Date: 
Jul 2004
Posts: 
663
TPC Rating: 
100% (5)
592m



Log in to see fewer ads
What can be done about this terrible trigger?
Reply With Quote
  #2  
Old 01-27-2019, 07:30 PM
M40A1
US Marines

Join Date: 
Feb 2007
Posts: 
9
TPC Rating: 
100% (1)
https://www.rimfirecentral.com/forum...d.php?t=467194
Reply With Quote
  #3  
Old 01-27-2019, 08:18 PM
Balvar24
NRA Member - Click Here To Join!

Join Date: 
Jul 2004
Posts: 
663
TPC Rating: 
100% (5)
Thanks!
Reply With Quote
Sponsored Links
Advertisement
 
  #4  
Old 01-27-2019, 08:51 PM
Al the Infidel's Avatar
Al the Infidel
US Marines Disabled American Veteran NRA Member - Click Here To Join!

Join Date: 
Jan 2007
Location: 
Yoopersville, MI
Posts: 
1,012,020
TPC Rating: 
0% (0)
Quote:
Originally Posted by M40A1 View Post
Great way to pluck a pigeon.
__________________
If we were serious about saving lives, our vehicles would have breathalyzers tied into ignition kill switches.
Reply With Quote
  #5  
Old 01-27-2019, 10:17 PM
HUSHKABOOM
NRA Member - Click Here To Join!

Join Date: 
Feb 2008
Location: 
Oregon
Posts: 
10,947
TPC Rating: 
100% (43)
I have used Earnie the Gunsmith 788 springs in several 591, 592, 581, 582 with good results. That is to say most have been ok 3-4 pound hunting triggers after the install. Better if some cleaning and polishing is done on the trigger parts.
http://erniethegunsmith.com/catalog/i20.html

Last edited by HUSHKABOOM; 01-27-2019 at 10:20 PM.
Reply With Quote
  #6  
Old 01-27-2019, 10:32 PM
Balvar24
NRA Member - Click Here To Join!

Join Date: 
Jul 2004
Posts: 
663
TPC Rating: 
100% (5)
I dusted off my 592 today. At 150 yds, I had 3" groups. My crown needs some work. I had to cut the barrel back to 19.25" a couple of years ago. Didn't really know what I was doing. It looks good, but the powder residue says otherwise.
Reply With Quote
  #7  
Old 01-29-2019, 03:02 AM
theriddler1977's Avatar
theriddler1977

Join Date: 
Oct 2015
Posts: 
123
TPC Rating: 
0% (0)
Not sure if they make one of these for a 5mm or not but I considered trying one on a Browning BL-22 project gun
https://www.midwayusa.com/product/66...17-218-219-236
Not ideal but we don't all have the luxury of a lathe
Reply With Quote
  #8  
Old 01-29-2019, 08:06 AM
Al the Infidel's Avatar
Al the Infidel
US Marines Disabled American Veteran NRA Member - Click Here To Join!

Join Date: 
Jan 2007
Location: 
Yoopersville, MI
Posts: 
1,012,020
TPC Rating: 
0% (0)
Put this in your drill press, drill, or whatever and apply cutting oil frequently. https://www.brownells.com/gunsmith-t...aspx?rrec=true
__________________
If we were serious about saving lives, our vehicles would have breathalyzers tied into ignition kill switches.
Reply With Quote
  #9  
Old 01-29-2019, 09:47 AM
Balvar24
NRA Member - Click Here To Join!

Join Date: 
Jul 2004
Posts: 
663
TPC Rating: 
100% (5)
My father-in-law and I cut a target crown on it in the lathe. I think it needs polishing more than anything. I did the brass screw thing, maybe over did it. I thinking I need a 45 degree brass polishing tool.
Reply With Quote
  #10  
Old 01-29-2019, 10:44 AM
Al the Infidel's Avatar
Al the Infidel
US Marines Disabled American Veteran NRA Member - Click Here To Join!

Join Date: 
Jan 2007
Location: 
Yoopersville, MI
Posts: 
1,012,020
TPC Rating: 
0% (0)
Quote:
Originally Posted by Balvar24 View Post
My father-in-law and I cut a target crown on it in the lathe. I think it needs polishing more than anything. I did the brass screw thing, maybe over did it. I thinking I need a 45 degree brass polishing tool.
A smaller screw head increases the angle IME. I use brass phillips screws and spin em up on 600 grit paper in a drill to remove any burrs before touching up a crown.
__________________
If we were serious about saving lives, our vehicles would have breathalyzers tied into ignition kill switches.
Reply With Quote
  #11  
Old 01-29-2019, 11:44 AM
Balvar24
NRA Member - Click Here To Join!

Join Date: 
Jul 2004
Posts: 
663
TPC Rating: 
100% (5)
I was thinking about having a 45 degree angle turned on a piece of round stock?

Of course, I was using an old 4 power scope (out side it's parallax adjustment range) as well. I'm sure that didn't help.

Last edited by Balvar24; 01-29-2019 at 11:46 AM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Rem 592M, Anyone Re Barreled To Bionicman 5mm Mag 10 01-23-2019 05:04 AM
Remington 582 - 592m stocks Zapone13 5mm Mag 2 01-21-2019 09:10 AM
Remington 592M 5mm LJS Rimfirecentral TECH Support 0 10-22-2018 12:13 PM
592M Rigged up - Think I'll keep it Tuffbuff 5mm Mag 1 08-14-2017 07:12 PM



All times are GMT -5. The time now is 05:10 PM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x