The Titan Spike is here finally! - Page 2 - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > >

Notices

Join Team RFC to remove these ads.
Reply
 
Thread Tools Display Modes
  #16  
Old 08-06-2019, 04:42 PM
2Barrels
US Air Force Veteran NRA Member - Click Here To Join!

Join Date: 
Oct 2014
Location: 
SE Wisc
Posts: 
49
TPC Rating: 
0% (0)


Log in to see fewer ads
This is the info I was looking for when I came here and searched! Well done Michael!

Quote:
Originally Posted by Michael Victor View Post
Hello Gents,

We have just released our latest upgrade for our Titan 1022 Stock... the Titan Spike Anchor.

This simple device gives your Titan stock a second point of engagement to increase consistency and accuracy. It's very easy to install and with the supplied tools, you will be able to tune it for the best performance for your action.

The Spike actually presses down against the rear of the 10/22 receiver and holds it in place. You will need to play around with how much pressure to put on it but we have found 8-15 inch pounds works well.

One thing to keep in mind is the Spike is a SPIKE, so it will mark the back of your receiver. If you do not want a mark on the back of your receiver then don't use the SPIKE : )

If you receiver has a cleaning rod hole, the Spike will fit without a problem.

Here are some pics- let me know if you have questions or thoughts. I'm here to help!

Best,

Michael V.

(Btw- you can purchase it here: www.victorcompanyusa.com)














Reply With Quote
  #17  
Old 08-10-2019, 03:26 PM
Michael Victor's Avatar
Michael Victor
RFC Sponsor
NRA Member - Click Here To Join!

RFC Sponsor
Join Date: 
Oct 2013
Location: 
Los Angeles, CA
Posts: 
248
TPC Rating: 
100% (1)
We've been getting great feedback on the Spikes. Solid accuracy increases.

If you don't have a Kidd or other way to lock down the back of the action, it's best to use a Titan Spike to hold it down.

It's super easy to install in a Titan, only takes a couple minutes.
__________________


TITAN 1022 Upgrade now!
Reply With Quote
  #18  
Old 08-14-2019, 07:38 AM
Treefeller22
US Army Veteran

Join Date: 
May 2019
Location: 
Brisbane, Australia
Posts: 
19
TPC Rating: 
0% (0)
Are you shipping to Australia?
Reply With Quote
  #19  
Old 08-15-2019, 01:23 PM
Michael Victor's Avatar
Michael Victor
RFC Sponsor
NRA Member - Click Here To Join!

RFC Sponsor
Join Date: 
Oct 2013
Location: 
Los Angeles, CA
Posts: 
248
TPC Rating: 
100% (1)
Quote:
Originally Posted by Treefeller22 View Post
Are you shipping to Australia?

We have a Australian dealer, though they do not have the Spikes yet so you can order from our website if you want one now. (yes we ship direct)

https://www.australiantacticalprecis...victor-company

Thanks!
__________________


TITAN 1022 Upgrade now!
Reply With Quote
  #20  
Old 09-28-2019, 11:38 AM
Sagittarius

Join Date: 
Mar 2017
Posts: 
25
TPC Rating: 
0% (0)
The Spike should be offered with a nylon or polymer tip to avoid marking the receiver, for those who don't like the damage caused by it.
Reply With Quote
  #21  
Old 09-28-2019, 12:19 PM
wrencher

Join Date: 
Sep 2006
Location: 
Kalifornia
Posts: 
33
TPC Rating: 
0% (0)
That would defeat the purpose. A soft tip would deform and be loose.
Reply With Quote
  #22  
Old 09-28-2019, 05:36 PM
schiada96
NRA Member - Click Here To Join!

Join Date: 
Mar 2011
Location: 
Eden NC
Posts: 
93
TPC Rating: 
0% (0)
Quote:
Originally Posted by wolfshoon View Post
So you are not worried about stress fractures/cracking originating out of the gouge the Spike puts in the back of the receiver? That is pretty close edge distance to the bottom.


I don’t know that I would worry about the receivers made from extruded bar stock or the steel ones,but the Ruger 356 castings might be a problem.


Sent from my iPhone using Tapatalk
Reply With Quote
  #23  
Old 09-28-2019, 07:49 PM
Nick7274's Avatar
Nick7274
NRA Member - Click Here To Join! GOA Member

Join Date: 
Dec 2016
Location: 
Central Ma.
Posts: 
3,083
TPC Rating: 
100% (11)
This is not going to have any negative effect on any type of 10/22 receiver. It's a tiny little divot in the very back of the receiver. Drilling a cleaning hole in the back has never had any negative effect that I can think of, so why would this?
Reply With Quote
  #24  
Old 09-28-2019, 08:28 PM
schiada96
NRA Member - Click Here To Join!

Join Date: 
Mar 2011
Location: 
Eden NC
Posts: 
93
TPC Rating: 
0% (0)
Quote:
Originally Posted by Nick7274 View Post
This is not going to have any negative effect on any type of 10/22 receiver. It's a tiny little divot in the very back of the receiver. Drilling a cleaning hole in the back has never had any negative effect that I can think of, so why would this?


I don’t think it will be a problem. The cleaning rod hole is in the middle of the wall. This is on the edge of a casting with a point so it could be a problem with excess torque.


Sent from my iPhone using Tapatalk
Reply With Quote
  #25  
Old 09-29-2019, 10:57 AM
Sagittarius

Join Date: 
Mar 2017
Posts: 
25
TPC Rating: 
0% (0)
Quote:
Originally Posted by wrencher View Post
That would defeat the purpose. A soft tip would deform and be loose.
I read, the pressure on the rear of the action shouldn't be over 8-10 inch-pounds so that shouldn't be a problem for a nylon tip.
Actually, a brass tip would probably be even better since it's softer than aluminum but stronger than nylon.
Reply With Quote
  #26  
Old 09-29-2019, 11:10 AM
DGF

Join Date: 
Dec 2016
Location: 
Ontario Canada
Posts: 
806
TPC Rating: 
0% (0)
Won’t it go blunt after a number of tear downs for cleaning.
Reply With Quote
  #27  
Old 09-29-2019, 01:48 PM
schiada96
NRA Member - Click Here To Join!

Join Date: 
Mar 2011
Location: 
Eden NC
Posts: 
93
TPC Rating: 
0% (0)
Quote:
Originally Posted by Sagittarius View Post
I read, the pressure on the rear of the action shouldn't be over 8-10 inch-pounds so that shouldn't be a problem for a nylon tip.

Actually, a brass tip would probably be even better since it's softer than aluminum but stronger than nylon.


Brass is not softer than most aluminums surly not softer than a factory Ruger A356 casting


Sent from my iPhone using Tapatalk
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
FINALLY warm enough in Minnesota for some ammo testing! StevieTimes .22 Ammunition (S-L-LR) 11 03-09-2019 08:20 PM
Buy Kidd receiver or wait on Victor Titan Spike??? cahillxd 10/22 Action 13 02-26-2019 11:33 PM
Remington 121 finally running great And a Warning gokyo Remington 1 03-17-2018 01:18 AM
Help me decide on a stock; Magpul X-22, Titan 1022, At-One War_Machine 10/22 Stocks - Factory & Aftermarket 16 10-02-2017 10:09 PM
Bed a Revolution Extreme stock, or get a Victor Titan 1022 stock? ethan83 10/22 Stocks - Factory & Aftermarket 4 09-29-2017 03:35 AM



All times are GMT -5. The time now is 04:36 AM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©2000-2018 RimfireCentral.com
x