Dialing in a Plain Jane - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > >

Notices

Join Team RFC to remove these ads.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-25-2019, 05:01 PM
Bigbore
NRA Member - Click Here To Join!

Join Date: 
May 2002
Location: 
Miami, Fl
Posts: 
867
TPC Rating: 
0% (0)
Dialing in a Plain Jane



Log in to see fewer ads
I put this rifle together with leftovers with the exception of a new Green Mountain standard profile barrel, I want to see how they perform compared to the heavy taper style. The Ruger All Weather stock shown was an interference fit at the front of the barrel channel so I swapped it back to a Hogue Overmolded.

I went out to the range with the latest configuration without checking the winds and they were HOWLING. We've had a couple weeks with winds in the low to mid teens gusting to mid 20's mph.

Plain Jane has the Hogue stock(not pictured), JWH hammer pulling at ~3.5#'s Simmons 3-9 AO scope and GM barrel.


First trip out after restocking with the Hogue the wind was pretty bad, I'm not even going to waste my time measuring. I was experimenting with a rubber pad under the barrel at the front of the channel, the bottom two sets of SV, but...


I picked up a $6 puck of JB Marine Epoxy(?) at Lowes when I was there and did a quick lampshade bed job which turned out OK. The receiver seems to fit in the stock pretty snug so I only bedded one spot immediately in front of the take down screw, plenty of float. The receiver is locked in and the barrel rings like a piece of rebar set in concrete when I ping it.

Winds were better this morning. Wolf Target turned in the best groups of the day, Green Tag was the most expensive disappointment. I think with a trigger job the SV will get close to MOA. I'm challenging myself with only 10 shot groups and a 3-9 scope.


Last edited by Bigbore; 09-25-2019 at 05:05 PM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Plain Jane Build Finished RimfireRich22 SuperStock 46 07-13-2011 03:57 PM
Plain wood/killer test target longbow62 CZ / Brno 9 12-04-2010 09:21 PM
Plain grips for Supermatic Trophy Grads107 High Standard 2 11-06-2010 05:12 PM
Looking for nickel .22 standard velocity in plain box io333 .22 Ammunition (S-L-LR) 10 09-08-2004 12:36 AM
Patchworm Plain felt cleaning buttons anygood? thp38 CZ / Brno 3 08-13-2004 11:50 AM



All times are GMT -5. The time now is 02:19 AM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x