Takedown ftf

[Kjg26]

I took my take down out for the 1st time and had nothing but problems. I have the adjuster nut adjusted nice and snug. But I'm still having feeding issues. Several different manufacturers, same issue. Bx25 and factory 10 round mags. It tries to strip it out of the mag but doesn't seem to line up right with the chamber. Tried loosening the adjuster nut ever so slightly without any change. It's been suggested to try round nose bullets which I'll try tomorrow.

Any help?

[Toomany22s]

Scotch brite the inside of the receiver, the overspray interferes with the smooth operation of the bolt.
Make sure the stock is correctly lined up, there are little screws inthe receiver end/ face that let you do this.
Make sure the magazine well lets the magazine all the way in , sometimes there is flashing or other obstructions in the well sand them out.
Inspect the chambers mouth it should be smooth os butter, run a q tip over it if any cotton snags youve got a problem.
Clean and lube with Hornady one shot dri lube, the magazines too!
Assemble , turn the nob as tight as you can , then back off two clicks.
Without the magazine in the gun pull back the bolt a couple of times and let it slam shut. This seats the barrel.
Put the magazine in and shoot , it should run almost flawlessly, if not , call ruger get a return authorization and send it back.

[maximus83]

Could use a little more background info. For instance...

Is this a brand new rifle, or used but new to you?
Ruger 100% factory takedown, or some aftermarket parts? If so, which ones?
What types of ammunition did you you try? (Just off the cuff with what you provided, my first guess would be it's the ammunition).

[crackedcornish]

I'd scrub out the inside of the receiver of excess paint and apply some Hornady one shot dry lube

go through the owners manual to properly adjust the tension on the mechanism

try CCI MiniMags in the 10 round factory mags

[Kjg26]

Factory new rifle thats sat in my safe too long. Finally got out to shooting. I've got the adjuster as snug as I can and still able to assemble the rifle. Winchester and Remington hollow points.

I'll check out the reciever and chamber today.

Thanks all.

[Kjg26]

Can someone provide a link to the Hornady lube yall are referring to. All I see is 3 different case sizing lube. Dont think that's right.

[Nick7274]

Originally Posted by Kjg26

Toomany22s red or green scotchbrite? Does it matter. And is there a video of adjusting the screws on the forend? All I've adjusted is the large knurled nut thing.

Doesn't matter, I've used purple and green. Your just trying to get rid of any overspray inside the receiver.

Here is a link for the Hornady One Shot.

https://www.amazon.com/Hornady-9990-.../dp/B000LC9YM2

Also a VQ or Kidd extractor to replace the OEM one in your bolt may help. They're only about $10 and the first thing I change out in every one of my 10/22's. If you want to really slick up the action you could get a Kidd guide rod & springs ($10) and it will run like butter. Also some better ammo goes a long way.

https://www.coolguyguns.com/KIDD-Gui...-Kit_p_30.html

https://www.coolguyguns.com/KIDD-Extractor_p_14.html

[Kjg26]

I'll try and scuff it up when I get home. Don't want to swap out too many parts if I've got to send it to ruger. So what about the screws? What's the procedure with those?

[Kjg26]

Scuffed up. Nice and smooth.

https://photos.app.goo.gl/zD2aCKjScB9jBu9s5

Are these the screws you're referring to?

https://photos.app.goo.gl/n8euaeFYFFSLpcJo7

Breach is smooth and does not snag qtip

https://photos.app.goo.gl/xUuySdfjK9beoWwC6

[Kjg26]

Ok. Round nose bullets feed fine. Will i ever be able to run hollow points? After break in?

[FlysAlot]

Originally Posted by Kjg26

Ok. Round nose bullets feed fine. Will i ever be able to run hollow points? After break in?

try cci mini mags they will work just fine

[Nick7274]

Originally Posted by Kjg26

I'll try and scuff it up when I get home. Don't want to swap out too many parts if I've got to send it to ruger. So what about the screws? What's the procedure with those?

It will smooth out pretty easily. You'll see once you start doing it. It's actually pretty easy to give it almost a polished look. The extractor and charging handle are very easy to change back to OEM if you ever had to send it back to Ruger and may eliminate your problems. The guide rod isn't necessary (it does make the action a lot smoother) but I would recommend changing the extractor. Not sure what screws your referring to? As far as ammo hollow points should cycle fine but the 2 brands of ammo that you mentioned shooting are the last 2 I would ever run in my rifle's. They're fine for plinking but I wouldn't expect 100% reliability with them.

[Kjg26]

Thanks all. I think ruger is going to have to take a look at it.