Kimber 1911 22LR Help Please - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > > >

Notices

Join Team RFC to remove these ads.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-19-2021, 07:31 PM
rolltide is online now
NRA Member - Click Here To Join!

Join Date: 
Aug 2003
Posts: 
1,113
TPC Rating: 
100% (6)
Kimber 1911 22LR Help Please



Log in to see fewer ads
I recently picked up a Kimber 1911 Super Custom 22 LR pistol and am hoping for some help from those here who have had one.

I love the fit and feel of the pistol and have been very surprised by the accuracy. A good friend was so impressed by mine, that he went to a local shop that still had a new stainless model in stock, and purchased it.

We're both having the same issues.

Whether I use the factory magazine or any of the Pro-Mag magazines that I purchased after getting the pistol, I get malfunctions from time to time.

There is no consistency to them either from the standpoint of the magazine being used, or the number of rounds in the magazine.

When it runs, it's great...but when it doesn't, it's a pain...

These are the issues we're both seeing...

1. The slide seems to run over the next round in the magazine without chambering it.

2. The slide will not go all the way to the rear, thus leaving a fired round to hand up in the ejection port.

3. The slide will pick up the next round in the magazine, but only partially chamber it.

While mine was purchased used, his was new old stock.

The pistols seem to do these things randomly, regardless of the magazine or ammo used.

We've debated replacing magazine springs, recoil springs, polishing the rails, polishing the inside of the magazines or followers...

Has anyone had any of these issues in the past?

If so, how did you fix it?

We haven't reached out to Kimber yet, but I'm not even sure how they would handle it since they no longer offer these for sale.

Any and all help is greatly appreciated.
Reply With Quote
  #2  
Old 07-19-2021, 09:23 PM
carbineone

Join Date: 
Dec 2011
Posts: 
1,575
TPC Rating: 
100% (1)
Does the slide move freely with the recoil spring and such all out? Sounds like you may have a binding problem somewhere.Maybe the feed lips are bent on the mag and binding..I think the GSG mags may work in a Kimber..They are great mags if they will..They run way better in my Colt 22 Conversion than the original Colts do..

Does the mag seem to seat all the way in? Maybe the magazine catch is wore in the frame, or the the slot in the magazine?? Did Kimber use plastic magazines or the steel?

Look for unusual wear marks inside everything..Good Luck..Hope you get it going soon..
Reply With Quote
  #3  
Old 07-19-2021, 09:53 PM
NVaVettes
NRA Member - Click Here To Join!

Join Date: 
Dec 2010
Posts: 
843
TPC Rating: 
100% (2)
Rolltide:

You must be referring to the Kimber 1911 "Rimfire Super" by your description of its behavior . . .

I absolutely agree with the points you like about it: handles great and is surprisingly accurate!
So much so, that I picked up a second one. Both were picked up lightly used
at an 'acceptable' price. (As always, acceptable is relative.)

Anyhow, yes they can sometimes be a little 'fussy'. Here's my thoughts . . .

They seem to run better with hotter ammo.

Think high velocity, Mini-Mags, etc.
I've got a supply of old Winchester Super-X that makes them go pretty well.
(I have had the least failures with Mini-Mags though I don't like to make a steady diet of them.
They can be a little rough on other 22 pistols, but the Kimbers seem ok with them. )

They like to be clean.

Who doesn't?

They like a generous application of a quality thin lubricant.

(Yes, this usually aggravates the 'keep it clean' problem, depending on ammo.)

I can get away with CCI SV if the gun is clean and well lubed for at least part of a shooting session.

I can also tell as soon as it starts getting too dirty.

The magazine springs strike me as the weakest springs on any 22 magazine.

They are super easy to load, even without a button to help depress the follower, but . . .

I suspect this choice was to minimize the friction on the slide by the highest round in the magazine,
in a bid to help the gun run on standard velocity ammo.

However, I would bet a stronger spring would make sure the top round is more
reliably presented to the slide as long as the slide is pushed all of the way back.

Don't know if any other 1911-22 style magazine springs are stronger and would fit the mag housing?

I suppose one could experiment with a lighter recoil springs if one could find a source for candidates

So, will running a higher velocity ammo cause the aluminum slide to beat on the
aluminum frame and shorten the guns life?

I haven't seen any warning signs yet, fingers crossed.

I think the thing to do is to keep trying CCI SV every once in a while to see if they will run it after things
are more broken in. If they do, I'll switch to them.

Good luck with yours!

Don

Last edited by NVaVettes; 07-20-2021 at 07:01 PM.
Reply With Quote
Sponsored Links
Advertisement
 
  #4  
Old 07-20-2021, 09:23 PM
Happy Kaboomer

Join Date: 
Jul 2008
Posts: 
118
TPC Rating: 
0% (0)
Send the pro mags to someone you don't like and buy some that are much better.
Reply With Quote
  #5  
Old 07-20-2021, 09:38 PM
Henry88's Avatar
Henry88

Join Date: 
Nov 2014
Location: 
Central Florida
Posts: 
795
TPC Rating: 
0% (0)
Avoid bulk ammo especially fed automags. takes mags apart and deep clean including spring. don't over lube would be my thoughts.
Reply With Quote
  #6  
Old 07-21-2021, 08:49 AM
rolltide is online now
NRA Member - Click Here To Join!

Join Date: 
Aug 2003
Posts: 
1,113
TPC Rating: 
100% (6)
Thanks for the replies!

I neglected to mention the ammo. We've tried Mini-Mags, Eley Force, which is what we use in Steel Challenge, as well as standard velocity ammo.

The issues seem consistent, regardless of ammo.

The Pro Mags function as well as the factory mags, so they don't seem to be an issue.

I think we're going to go down the rabbit hole, one item at a time to see if we can diagnose the issue.

Thanks again!
Reply With Quote
  #7  
Old 07-21-2021, 07:37 PM
VASCAR2
NRA Member - Click Here To Join!

Join Date: 
Sep 2008
Posts: 
938
TPC Rating: 
0% (0)
I find it very helpful to polish the chamber on 22 rimfires. I use Flitz on a barrel mop on a short cleaning rod attached to a hand drill. I also changed the hammer spring on my 1911 pistol frames. The factory hammer spring is 23 pounds. I use Wolff 18 pound hammer spring with my AA standard 1911 kit. I built a dedicated RIA 1911 frame and used the 18 pound hammer spring. I used the frame on my RIA 1911 A-1 frame until I built a dedicated frame. I changed the 23 pound spring to a 18 pound spring and have never had a problem igniting centerfire or rimfire ammo with the lighter hammer spring.
Reply With Quote
  #8  
Old 07-25-2021, 12:09 PM
beb42503

Join Date: 
Jul 2002
Location: 
KY
Posts: 
874
TPC Rating: 
100% (3)
I do not think this has anything to do with the problem on your Kimber but will share what mine does not like. It is a single shot jam o matic with Winchester Wildcat HV and I do not know why. It functions flawless with CCI Mini Mag, Blazer, Remington GB, & Bulk Federal HV. It jams with Federal Auto Match about 50% of the time and about the same with any standard velocity. My Kimber unit is mounted on a S&W Target .45 with factory springs. Best of luck in solving your issue!
Reply With Quote
  #9  
Old 07-30-2021, 03:10 PM
anoblefox's Avatar
anoblefox
US Navy Veteran NRA Member - Click Here To Join!

Join Date: 
Nov 2003
Posts: 
102
TPC Rating: 
0% (0)
After many rounds downrange the magazine round follower tends to hang up within the magazine body from powder residue buildup. After a good cleaning I have found that application of spray graphite inside and on the follower helps. You can depress the follower down against the spring to check for possible binding. As mentioned the spring is quite weak and it does not take much bind on the follower to experience a problem feeding. I have a little over 3k rounds through mine and can report that the feed ramp will get a slight notch from many rounds and needs to be smoothed out with a dremel and cratex bullet burr to restore full reliability. Also needs lots of lube on the slide as stated; when I got mine used the frame had a very small burr and it slowed the slide just enough to cause misfeeds. By far this gun gets more range time and more rounds through it than any of my other pistols for sure!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off




All times are GMT -5. The time now is 09:38 AM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x