52e international match disassembly help - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > > >

Notices

Join Team RFC to remove these ads.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-08-2021, 07:43 PM
Johnymango

Join Date: 
Apr 2018
Posts: 
81
TPC Rating: 
0% (0)
52e international match disassembly help



Log in to see fewer ads
I recently got a 52e international match and I'm having a hard time separating the barrel from the stock. I removed the screw behind the bolt, and the Allen bolt in front of the trigger. The barrel isn't budging at all. Are there any screws I'm missing? I don't think it's ever been apart and I don't want to start tapping it with a nylon hammer if there's a screw I'm missing. Thanks
Reply With Quote
  #2  
Old 06-08-2021, 08:33 PM
justinp61
NRA Member - Click Here To Join!

Join Date: 
Jun 2012
Location: 
W.KY Go Cards & Wildcats
Posts: 
1,052
TPC Rating: 
100% (2)
I donít have a International but on my E there is a slotted screw in the rail that is the front action screw.
Reply With Quote
  #3  
Old 06-08-2021, 09:19 PM
Seewin
NRA Member - Click Here To Join!

Join Date: 
Nov 2003
Location: 
MO
Posts: 
3,423
TPC Rating: 
100% (69)
Only 2 screws hold the barreled action in stock. The front screw is an allen head cap screw that goes through accessory rail. Rear is a slotted screw w/nut that go's through the tang at rear.
Steve
Reply With Quote
Sponsored Links
Advertisement
 
  #4  
Old 06-09-2021, 07:03 AM
pump .22s's Avatar
pump .22s
NRA Member - Click Here To Join!

Join Date: 
Dec 2010
Location: 
Deep East Texas
Posts: 
12,298
TPC Rating: 
0% (0)
This is unlikely, and you are probably not as dumb as I am, but after removing the bolt I once loosened the rear trigger screw instead of the action screw behind it. Not paying attention I suppose, but it took me a ten count to figure out why the barreled action was not loose from the stock.
Reply With Quote
  #5  
Old 06-09-2021, 07:26 AM
dokey
Law Enforcement Officer NRA Member - Click Here To Join!

Join Date: 
Jan 2008
Location: 
NY
Posts: 
1,301
TPC Rating: 
100% (10)
The 52 International Receivers Were bedded with a reddish bedding compound. Also there was a recoil lug attached to the bottom of the receiver which makes a very tight fit between the action and stock. Try tapping the barrel with a rubber mallet. If that doesn't work find a long screw with the same thread as the Allen screw, thread it into the receiver and tap it with a hammer

Last edited by dokey; 06-09-2021 at 07:37 AM.
Reply With Quote
  #6  
Old 06-11-2021, 08:31 AM
Johnymango

Join Date: 
Apr 2018
Posts: 
81
TPC Rating: 
0% (0)
I got it out with some taps of the hammer. Thanks guys
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off




All times are GMT -5. The time now is 12:46 PM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright ©2000-2018 RimfireCentral.com
x