BigMike's 10/22 Action Reference Section - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > >

Notices

Join Team RFC to remove these ads.
Closed Thread
 
Thread Tools Display Modes
  #1  
Old 12-11-2003, 09:34 AM
BigMike

Join Date: 
Mar 2002
Posts: 
5,131
TPC Rating: 
0% (0)
Post BigMike's 10/22 Action Reference Section



Log in to see fewer ads
Gentlemen,

I have consolidated all of the "Sticky" Posts on the "10/22 Action" Forum into this one thread. Although it will not be quite as visible as the former single "Sticky" Posts were, it will make the general viewing of the "10/22 Action" Forum much easier.

10/22 Action Reference Section Index:
1. Bolt Handles Compared: LR vs Mag vs PC
2. Auto Bolt Release Picture
3. 10/22 Trigger Group Disassembly
4. 10/22 Exploded View
5. Magazine Service
6. BX-1 Verses JX-1 Magazines
7. 10/22 Bolt Chamfering
8. Stovepiping

If there are any problems with this set-up, please contact me via PM.





.

Last edited by DrGunner; 03-08-2017 at 03:41 PM. Reason: Renamed after BigMike
  #2  
Old 12-11-2003, 09:39 AM
BigMike

Join Date: 
Mar 2002
Posts: 
5,131
TPC Rating: 
0% (0)
Post Bolt Handles Compared: LR vs Mag vs PC

Click on the Link below for this Section:

Bolt Handles Compared: LR vs Mag vs PC


  #3  
Old 12-11-2003, 09:42 AM
BigMike

Join Date: 
Mar 2002
Posts: 
5,131
TPC Rating: 
0% (0)
Post Auto Bolt Release Picture

Click on the Link below for this Section:

Auto Bolt Release Picture


Sponsored Links
Advertisement
 
  #4  
Old 12-11-2003, 09:46 AM
BigMike

Join Date: 
Mar 2002
Posts: 
5,131
TPC Rating: 
0% (0)
Post 10/22 Trigger Group Disassembly

Click on the Link below for this Section:

10/22 Trigger Group Disassembly


  #5  
Old 12-11-2003, 09:50 AM
BigMike

Join Date: 
Mar 2002
Posts: 
5,131
TPC Rating: 
0% (0)
Post 10/22 Exploded View

Click on the Link below for this Section:

10/22 Exploded View


  #6  
Old 12-11-2003, 10:00 AM
BigMike

Join Date: 
Mar 2002
Posts: 
5,131
TPC Rating: 
0% (0)
Post Magazine Service

Click on the Link below for this Section:

Magazine Service


  #7  
Old 12-11-2003, 10:03 AM
BigMike

Join Date: 
Mar 2002
Posts: 
5,131
TPC Rating: 
0% (0)
Post BX-1 Verses JX-1 Magazines

Click on the Link below for this Section:

BX-1 Verses JX-1 Magazines


  #8  
Old 12-13-2003, 12:27 PM
BigMike

Join Date: 
Mar 2002
Posts: 
5,131
TPC Rating: 
0% (0)
Post 10/22 Bolt Chamfering

Click on the Link below for this Section:


EDIT: The original link BigMike referenced is gone. I've replaced it with the following by Antlurz:

Chamfering the 10-22 Bolt by Antlurz

Respectfully,

DrGunner



Last edited by DrGunner; 03-08-2017 at 03:12 PM. Reason: Replaced broken link
  #9  
Old 03-15-2004, 07:08 AM
BigMike

Join Date: 
Mar 2002
Posts: 
5,131
TPC Rating: 
0% (0)
Post Stovepiping

Stovepiping: the partial ejection of a fired case, usually leaving the open mouth of the case sticking out of the ejection port, looking like a "stove pipe", and thus jamming the action of a semi-automatic firearm.

Stovepiping is caused by the slow or incomplete cycling of the bolt...! !

Causes of the slow or incomplete cycling of the 10/22's bolt:
0 Gummed-up action: the Ruger applied ‘preservative’ was not removed before firing, or oil was used as a lube...! !
0 Rifle was stored vertically after cleaning, allowing oil to run into the action & gum-it-up...! !
0 Unlubed or rough "Bolt Handle Guide Rod" [B-7]...! !
0 Action not lubed with a dry Teflon type spray lube or "CLP"...! !
0 Action not 'broken-in' yet..! ! Normally it takes 1 - 2 bricks [500 rds ea.] of High Velocity ammo to ‘break-in’ a 10/22's action...! !
0 Use of Standard Velocity or Sub Sonic ammo...! !
0 Aftermarket action parts misinstalled...! !
0 Scope base mounting screws rubbing on the top of the bolt.
0 "Hammer Strut Assembly" reassembled with the 'slot' of the "Retaining Washer" facing down; it must face UP...! !
0 Use of a non Ruger magazine...! ! Use a Ruger BX-1...! !
0 Magazine not seating with a 'click'...! !
0 Dirty or untuned magazine(s); see the "Sticky" Post at the top of this Forum for "Magazine Service"...! !
0 Magazine touching the stock in magazine well; can you pass a business card up both sides of the magazine all-the-way to the receiver...? ?

Note: The 10/22 is a "blow back" action, and it does not need an "extractor" to extract and eject fired rounds...! ! The “extractor” is only need to extract unfired rounds...! ! The primary "ejector" is the last 1/4" of the left lip of the BX-1's magazine throat...! !

You will have to see which cause(s) best fit(s) your particular situation...! !

Hope this helps....! !


Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off




All times are GMT -5. The time now is 03:11 AM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©2000-2018 RimfireCentral.com
x