Firing Pin advice from Calfee - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > >

Notices

Join Team RFC to remove these ads.
Closed Thread
 
Thread Tools Display Modes
  #1  
Old 01-16-2006, 07:08 AM
mistermike's Avatar
mistermike
US Navy Veteran NRA Member - Click Here To Join!

Join Date: 
Jun 2002
Location: 
Massachusetts
Posts: 
1,151
TPC Rating: 
0% (0)
Firing Pin advice from Calfee



Log in to see fewer ads
I've been keeping notes of information about the Suhl 150. I found this on another board and wish I could properly cite its source, but I don't think Bill would mind my passing on the information... Michael

"Calfee Firing Pin Spring -
Friend jayb:

Suhl's need a good mainspring because of the round shape and large tip size of the firing pin...old Suhl springs weaken over the years...
You can obtain new Extra Power spring from Wolff springs @ 1-800-545-0077.
I use the spring for the 1700 series Anschutz, which is their stock number # 30463. This spring will interchange with the old Suhl spring just fine.

Now, you must listen to this carefully please:

The cocking piece for the Suhl firing pin is threaded on. When you replace the spring you must remove the jam nut, which is staked in place, then very carefully measure the distance from the rear end of the firing pin to the back edge of the cocking piece.

When you install the new spring, the cocking piece must be threaded back to the exact same location on the pin...you can't miss this even a few thousandths of an inch. Here's why. The Suhl firing pin is mechanically stopped by a shoulder on the pin striking a counterbore inside the front of the bolt body. So if your firing pin protrusion, the amount that the pin sticks past the opening in the bolt nose, is proper now, it will be proper after you change the spring..
BUT, what you can do if you don't get the cocking piece back exactly like it was before, is one of two things; First, if it is screwed on too short, you won't pre-load the firing pin spring enough and ignition will be crummy....and second, if you screw it in too far, then the firing pin will no longer be mechanically stopped by the factory method, no, it will then be stopped by the cocking piece striking the bottom of the cocking cam in the bolt body...this can break your firing pin should you ever dry fire it.


Changing Suhl firing pin springs should be left to a very experienced gunsmith who fully understands the pitfalls of doing it incorrectly."
  #2  
Old 12-04-2012, 07:03 PM
kd4oro

Join Date: 
May 2010
Posts: 
1
TPC Rating: 
0% (0)
Firing Pin

Great info Mr. Mike. Thank you.
I recently discovered a broken jam nut and some other parts in my bolt assembly and need to get it reworked. Would you have any recommendations as to who might could help me with this?
Thanks in advance.
  #3  
Old 02-08-2013, 03:30 PM
bullseye4845's Avatar
bullseye4845
US Army Veteran NRA Member - Click Here To Join!

Join Date: 
Oct 2005
Location: 
Northwest, Georgia
Posts: 
542
TPC Rating: 
100% (2)
Firing Pin advice from Calfee

I changed my fp to a Wolf, 1700 Anchutz spring, and works great with a much
deeper indent strike. The Wolf spring is a little longer and stronger.
Be sure to measure the distance as indicated on the Suhl sticky. Use your dial caliper, and it is no problem. It is a good time to polish the bolt parts that are
rubbing, and clean with lighter fluid.
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off




All times are GMT -5. The time now is 03:28 PM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x