Kingston M1 Garand - Page 12 - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > >

Notices

Join Team RFC to remove these ads.
Reply
 
Thread Tools Display Modes
  #166  
Old 12-03-2019, 12:10 PM
Rimfire Sports's Avatar
Rimfire Sports
RFC Sponsor
NRA Member - Click Here To Join!

RFC Sponsor
Join Date: 
Mar 2002
Location: 
Ashburn, Virginia
Posts: 
307
TPC Rating: 
0% (-1)


Log in to see fewer ads
Quote:
Originally Posted by LorenatBMS View Post
Have you removed the front hand guards and the hand guard metal that fits around the barrel?
Have not as I'm not sure how to get them off. How do you get the handguard metal off?
__________________
Alan

Rimfire Sports & Custom - RFC Sponsor
Reply With Quote
  #167  
Old 12-03-2019, 01:04 PM
LorenatBMS

Join Date: 
May 2016
Posts: 
205
TPC Rating: 
0% (0)
Take a look at post #14 here.

https://www.rimfirecentral.com/forum...d.php?t=712681

Three set screes on the bottom side of the fake gas block/tube. Loosen them and the gas tube slides off, as do the hand guards.
Reply With Quote
  #168  
Old 12-03-2019, 01:51 PM
Rimfire Sports's Avatar
Rimfire Sports
RFC Sponsor
NRA Member - Click Here To Join!

RFC Sponsor
Join Date: 
Mar 2002
Location: 
Ashburn, Virginia
Posts: 
307
TPC Rating: 
0% (-1)
Those front two must be Loctited in as I can't budge them.
__________________
Alan

Rimfire Sports & Custom - RFC Sponsor
Reply With Quote
  #169  
Old 12-03-2019, 02:08 PM
LorenatBMS

Join Date: 
May 2016
Posts: 
205
TPC Rating: 
0% (0)
I would put some heat on them to help break the Loctite.
Reply With Quote
  #170  
Old 12-03-2019, 03:22 PM
izhm
NRA Member - Click Here To Join!

Join Date: 
Dec 2015
Posts: 
272
TPC Rating: 
100% (1)
You need to find the correct allen wrench to remove the front gas cylinder and slide it off the barrel ,than the front hand guard and the rear hand will slide forward off of the barrel .Back out the take down screw and lift the barreled action just like a standard 10/22 . Use a electric soldering gun to heat the head of the allen screw and back it out.

Last edited by izhm; 12-04-2019 at 06:35 AM.
Reply With Quote
  #171  
Old 12-03-2019, 04:42 PM
Brad76

Join Date: 
Jul 2009
Location: 
Minnesota
Posts: 
39
TPC Rating: 
0% (0)
I got my Kingston M1 working this fall. I ended up putting in a Kidd Bolt and a Kidd charging handle and reduced power recoil spring. Running a standard 10/22 trigger pack.

I have been shooting CCI Blazer 40 grain, Federal Champion 40 grain, and Aguila Standard Velocity 40 grain, using Ruger BX-1 and BX-15 mags. I have put over 1000 rounds through it, and am averaging a failure ratio of less than 1% (I think I have had 5 stovepipes to date, but can't remember for sure - I am at work and my notes are at home).

Not the cheapest fix, but it is working reliably now and I am happy with it.

Good luck to all!

Brad
Reply With Quote
  #172  
Old 12-03-2019, 08:17 PM
M2HB's Avatar
M2HB
NRA Member - Click Here To Join!

Join Date: 
Apr 2004
Location: 
Phoenix, Arizona
Posts: 
28,763
TPC Rating: 
100% (4)
Quote:
Originally Posted by Brad76 View Post
I got my Kingston M1 working this fall. I ended up putting in a Kidd Bolt and a Kidd charging handle and reduced power recoil spring. Running a standard 10/22 trigger pack.

I have been shooting CCI Blazer 40 grain, Federal Champion 40 grain, and Aguila Standard Velocity 40 grain, using Ruger BX-1 and BX-15 mags. I have put over 1000 rounds through it, and am averaging a failure ratio of less than 1% (I think I have had 5 stovepipes to date, but can't remember for sure - I am at work and my notes are at home).

Not the cheapest fix, but it is working reliably now and I am happy with it.

Good luck to all!

Brad
It sounds like you have a good combination with the Kidd bolt and charging handle.
Reply With Quote
  #173  
Old 12-04-2019, 12:55 AM
bczrx's Avatar
bczrx
NRA Member - Click Here To Join!

Join Date: 
Mar 2011
Location: 
San Joaquin Valley, California
Posts: 
594
TPC Rating: 
100% (1)
First- loosen the 3 allen screws in the base of the front sight piece. Do NOT loosen the allen screw that allows drift adjustment on the front sight.

The correct ones are somewhat hidden on the bottom, and are small.
They are on the part that would hold the 'gas port' and gas tube on an M1 Garand, but they slide over a solid rod of steel instead.

Once those are loose, you can slide the entire front sight assembly off.

Once that is off, the handguards and other parts slide off the barrel- toward the muzzle. Once all of those loose parts are off, then you can remove the action from the stock [since you have loosened the stock/action bolt on bottom of rifle].

Reverse it to reinstall.
Reply With Quote
  #174  
Old 01-10-2020, 07:59 PM
lazershooter

Join Date: 
Jul 2012
Location: 
SE Ohio.
Posts: 
260
TPC Rating: 
0% (0)
NIB Kingston Garand

My apologies in advance if I'm breaking any rules by posting this.

A friend of mine who is a dealer has a Kingston Garand that's NIB if there is anyone here that's interested. It was ordered by him when Kingston first released the Garands. He ordered two, sold one but not the other... yet.

Send me a PM and I'll get you hooked up.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off




All times are GMT -5. The time now is 08:04 AM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x