Taping inside receiver re-visited - Page 2 - RimfireCentral.com Forums

Go Back   RimfireCentral.com Forums > >

Notices

Join Team RFC to remove these ads.
Reply
 
Thread Tools Display Modes
  #16  
Old 08-26-2019, 02:23 AM
CPC
RFC Sponsor
National Guard Veteran NRA Member - Click Here To Join!

RFC Sponsor
Join Date: 
Mar 2002
Location: 
Middletown CT, Earth, 1st door on the right
Posts: 
1,227
TPC Rating: 
96% (22)


Log in to see fewer ads
Opposite side of ejection port, all the way down inside receiver....
__________________
Randy at CPC.
Reply With Quote
  #17  
Old 08-27-2019, 07:23 PM
bullseye4845's Avatar
bullseye4845 is online now
US Army Veteran NRA Member - Click Here To Join!

Join Date: 
Oct 2005
Location: 
Northwest, Georgia
Posts: 
537
TPC Rating: 
100% (2)
Taping inside receiver re-visted

Randy, I think you are correct on the .005 tape, as I tried the .010, and was a little tight; however, it was smooth, and will have to try at range to see if it will cycle the target ammo. I may have to change to the .005.
Reply With Quote
  #18  
Old 08-27-2019, 07:41 PM
CPC
RFC Sponsor
National Guard Veteran NRA Member - Click Here To Join!

RFC Sponsor
Join Date: 
Mar 2002
Location: 
Middletown CT, Earth, 1st door on the right
Posts: 
1,227
TPC Rating: 
96% (22)
Maybe not... I would remove tape then take a stone and resurface tape area removing high spots... I use a short stone then degrease area with acetone... A lot of receivers are cast so there are low and high spots....
__________________
Randy at CPC.
Reply With Quote
  #19  
Old 09-03-2019, 11:40 PM
CarlsonCustoms

Join Date: 
Jul 2009
Posts: 
47
TPC Rating: 
0% (0)
I would not have even noticed Randy taped my receiver unless I looked. I can't argue with the results, as you can see in my article on RangeHot it outshot a $1800 Volquartsen gun.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
The GSG STG-44 THREAD - Dissasembly, cleaning/lubing and tips Marc780 Misc -- Other Rimfire Rifle Brands 34 08-19-2019 02:33 PM
Crooked barrel to receiver fit inspector12 Anything 10/22 7 02-27-2018 12:21 AM
Kidd Rear Tang on Fedderson 22XA Receiver azguy 10/22 Action 1 04-15-2017 01:53 PM
Receiver cover removal Asuaviator Henry 14 11-25-2016 12:19 PM
Kimber Kollege back in session VertFish Kimber 11 09-25-2016 09:03 PM



All times are GMT -5. The time now is 07:17 AM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x