RimfireCentral.com Forums - Search Results

Go Back   RimfireCentral.com Forums >

Join Team RFC to remove these ads.
Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: HUSHKABOOM
Forum: Remington 06-11-2021, 12:30 AM
Replies: 11
Views: 352
Posted By HUSHKABOOM
I measured 2 takedown bolts and both were about...

I measured 2 takedown bolts and both were about 1.290" overall length.
Forum: CZ / Brno 06-11-2021, 12:03 AM
Replies: 8
Views: 666
Posted By HUSHKABOOM
There were lots of Premiums on Gunbroker for a...

There were lots of Premiums on Gunbroker for a few months and then none! I looked for one with nice figure in the wood, didn't find one and then they were gone!
Forum: Remington 06-10-2021, 08:30 PM
Replies: 11
Views: 352
Posted By HUSHKABOOM
Nice condition early 581. Appears to have the...

Nice condition early 581. Appears to have the small ejection port. Walnut stock. Probably late 1967 to early 68. The date code is stamped on the left side of barrel just ahead of rear sight base....
Forum: CZ / Brno 06-10-2021, 01:09 PM
Replies: 5
Views: 388
Posted By HUSHKABOOM
Looks good but you may never find a replacement...

Looks good but you may never find a replacement rear sight for it.
Forum: Winchester 06-09-2021, 09:06 PM
Replies: 9
Views: 493
Posted By HUSHKABOOM
https://www.gunpartscorp.com/products/1597960 ...

https://www.gunpartscorp.com/products/1597960
https://www.gunpartscorp.com/products/1329460
https://www.gunpartscorp.com/products/1329450
Forum: Remington 06-09-2021, 08:57 PM
Replies: 27
Views: 1,125
Posted By HUSHKABOOM
Not factory. Could be a Canjar made trigger that...

Not factory. Could be a Canjar made trigger that was added. Also made for the 788.
Forum: Remington 06-09-2021, 08:55 PM
Replies: 27
Views: 1,125
Posted By HUSHKABOOM
521 is based on 511. Little brother to 513 target...

521 is based on 511. Little brother to 513 target rifles. Different than the later 541 581 series.
Forum: Remington 06-09-2021, 03:16 PM
Replies: 12
Views: 293
Posted By HUSHKABOOM
Nice one! Thanks for the photos.

Nice one! Thanks for the photos.
Forum: Winchester 06-08-2021, 12:02 AM
Replies: 9
Views: 493
Posted By HUSHKABOOM
what length is the fore end you seek? 8"? 9"?...

what length is the fore end you seek? 8"? 9"? Plain walnut?
Forum: Model 597 06-07-2021, 11:44 PM
Replies: 7
Views: 283
Posted By HUSHKABOOM
The early ones were blued. Matte like a glass...

The early ones were blued. Matte like a glass bead blast was done first. Could clean off rust with a Big 45 pad and maybe touch up with cold blue.
Forum: Remington 06-07-2021, 11:29 PM
Replies: 17
Views: 709
Posted By HUSHKABOOM
Smooth barrel and action. No threads. Special...

Smooth barrel and action. No threads. Special glue holds them together.
Forum: Remington 06-07-2021, 11:27 PM
Replies: 27
Views: 1,125
Posted By HUSHKABOOM
Good condition $600 super deal $700 good deal...

Good condition
$600 super deal
$700 good deal
$800 grab it if in good shape
$900 can be found if you shop around
$1000 I think this is to high unless it has an extra special stock
Forum: CZ / Brno 06-07-2021, 11:16 PM
Replies: 4
Views: 251
Posted By HUSHKABOOM
This large may be big enough? ...

This large may be big enough?
https://www.midwayusa.com/product/1115216674
Forum: Open Rimfire 06-06-2021, 11:52 PM
Replies: 14
Views: 1,179
Posted By HUSHKABOOM
The drill bits I have seen for sale have a pilot...

The drill bits I have seen for sale have a pilot close to the existing hole size to guide the bit as it bores the new size for liner. Seems like they also drill halfway + from each end?
Forum: Remington 06-06-2021, 04:58 PM
Replies: 19
Views: 1,406
Posted By HUSHKABOOM
You can buy a good condition original magazine...

You can buy a good condition original magazine from Ebay. Always some listed. It will have Remington in script stamped into the baseplate. The ones with just an R are aftermarket but will usually...
Forum: Remington 06-06-2021, 04:55 PM
Replies: 19
Views: 1,406
Posted By HUSHKABOOM
Yes 1961 with grooved receiver. Nice!

Yes 1961 with grooved receiver. Nice!
Forum: Custom Knives 06-06-2021, 12:37 PM
Replies: 4
Views: 244
Posted By HUSHKABOOM
Very nice knife!

Very nice knife!
Forum: Remington 06-06-2021, 12:14 PM
Replies: 19
Views: 1,406
Posted By HUSHKABOOM
1939 will probably have a serial number on bottom...

1939 will probably have a serial number on bottom of barrel just ahead of the stock. 1961 would probably have a grooved receiver for scope mounting.
Forum: Remington 06-06-2021, 12:08 PM
Replies: 5
Views: 264
Posted By HUSHKABOOM
I have not seen a drop in for the 541-581 series...

I have not seen a drop in for the 541-581 series of rifles. Don't remember seeing a drop in even back when the 541 was a very popular silhouette rifle.
Forum: Remington 06-05-2021, 11:59 AM
Replies: 7
Views: 382
Posted By HUSHKABOOM
I see one photo. I think I saw two before. I...

I see one photo. I think I saw two before. I don't know if the safety levers are interchangeable.
Forum: Winchester 06-05-2021, 12:31 AM
Replies: 9
Views: 493
Posted By HUSHKABOOM
https://www.gunpartscorp.com/gun-manufacturer/winc...

https://www.gunpartscorp.com/gun-manufacturer/winchester/94-22-series/94-22
Forum: Remington 06-03-2021, 08:48 PM
Replies: 17
Views: 709
Posted By HUSHKABOOM
I picked up that barrel and then a stock. Put...

I picked up that barrel and then a stock. Put together with 581 action. Worked fine.
Forum: Winchester 52 06-03-2021, 12:13 AM
Replies: 68
Views: 3,519
Posted By HUSHKABOOM
Seems like scopes similar to what are sold today...

Seems like scopes similar to what are sold today were available during the 52C years so would look ok.
Forum: Remington 06-02-2021, 01:01 AM
Replies: 5
Views: 431
Posted By HUSHKABOOM
Some good groups there! Remingtons seem to like...

Some good groups there! Remingtons seem to like RWS R50?
Forum: Remington 05-31-2021, 09:25 PM
Replies: 7
Views: 373
Posted By HUSHKABOOM
CCI standard velocity target can act like that...

CCI standard velocity target can act like that when closing a bolt. It is slightly longer than normal.
Showing results 1 to 25 of 500

 


All times are GMT -5. The time now is 06:47 PM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright ©2000-2018 RimfireCentral.com
x