RimfireCentral.com Forums - Search Results

Go Back   RimfireCentral.com Forums >

Notices

Join Team RFC to remove these ads.
Showing results 1 to 8 of 8
Search took 0.01 seconds.
Search: Posts Made By: carl r. crump
Forum: .17HMR 11-11-2009, 05:17 PM
Replies: 39
Views: 5,380
Posted By carl r. crump
17 Hmr Case Splits

I have found a few split cases new out of the box .So check the new stuff before you load and you may save yourself some grief.After shooting a couple mags in my CZ last week I noticed three on the...
Forum: RFC "Get Togethers" 10-27-2009, 04:25 PM
Replies: 150
Views: 12,286
Posted By carl r. crump
Crossville

Crossville at the Painter Community
Forum: Scopes, Sights, Rings & Mounts, and Other Optics 04-04-2009, 06:00 PM
Replies: 11
Views: 549
Posted By carl r. crump
scopes

I have one Monarch,two Leupold,and a Hawke MAP PRO 3x9x50 The first three are on centerfire 22's.The Hawke is on CZ varmint 22 L.R.If nothing goes wrong with Hawke to change my mind I will replace...
Forum: CZ / Brno 05-23-2008, 09:00 PM
Replies: 8
Views: 501
Posted By carl r. crump
roll pin

the O.D. of the roll pin is .162
Forum: CZ / Brno 05-23-2008, 08:51 PM
Replies: 8
Views: 501
Posted By carl r. crump
roll pin

yes it is a roll pin.What it does is take up the slack just as someone did in one the early write ups by useing stainless or aluminium tape wraped around this same pin.I did this, but after alot of...
Forum: CZ / Brno 05-23-2008, 07:26 PM
Replies: 8
Views: 501
Posted By carl r. crump
cz trigger work on the cheap

On my two 452's I took out the bradded front trigger pin.I then got a split pin that had the hole I.D. that was tight fit on O.D. of the pin.These split pins are made to be driven into holes and will...
Forum: CZ / Brno 05-23-2008, 06:47 PM
Replies: 0
Views: 145
Posted By carl r. crump
cz trigger work on the cheap

On my two 452's I took out the bradded front trigger pin.I then got a split pin that had the hole I.D. that was tight fit on O.D. of the pin.These split pins are made to be driven into holes and will...
Forum: RFC "Get Togethers" 03-18-2008, 10:36 AM
Replies: 150
Views: 12,286
Posted By carl r. crump
who's from Alabama

I'm from Painter, close to Crossville , Alabama
Showing results 1 to 8 of 8

 


All times are GMT -5. The time now is 01:33 PM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x