RimfireCentral.com Forums - Search Results

Go Back   RimfireCentral.com Forums >

Notices

Join Team RFC to remove these ads.
Showing results 1 to 25 of 99
Search took 0.01 seconds.
Search: Posts Made By: jerrypoller
Forum: Model 597 04-18-2014, 03:21 PM
Replies: 10
Views: 1,350
Posted By jerrypoller
So, finally got to try 'em out

and all three worked perfectly. I ran 40 rounds through each magazine and only had one round fail to elevate properly in the mag. It was about round 4 or 5 of 10 and it just kinda' stuck in the...
Forum: CZ / Brno 04-10-2014, 03:09 PM
Replies: 9
Views: 388
Posted By jerrypoller
Great thread. I just noticed a lateral wobble in...

Great thread. I just noticed a lateral wobble in my rear sight today. After reading this and the referenced posts, I took my brno apart and cleaned up the windage screws, etc.. As I put it back...
Forum: CZ / Brno 04-03-2014, 07:45 PM
Replies: 67
Views: 2,403
Posted By jerrypoller
I'm the same way. I rarely shoot more than 50...

I'm the same way. I rarely shoot more than 50 rounds at a session. BUT, that's still more ammo out faster than I'm able to source it into my cache. This shortage is giving me sleepless naps :D
Forum: CZ / Brno 04-03-2014, 07:00 PM
Replies: 67
Views: 2,403
Posted By jerrypoller
Kenny, I don't have much choice. I shoot at a...

Kenny, I don't have much choice. I shoot at a private indoor range with a 50' pistol/rimfire rifle line, and a couple of 100 yard rifle tubes. The local outdoor range I used to "live" at closed...
Forum: CZ / Brno 04-03-2014, 05:49 PM
Replies: 67
Views: 2,403
Posted By jerrypoller
Well, I don't know if I'll ever do it, but my...

Well, I don't know if I'll ever do it, but my goal is to shoot 10 Xs at 100 yards on an NRA target. I may have shot the best group I ever will with 5 Xs at 100 yds the other day, but I'll keep...
Forum: CZ / Brno 04-03-2014, 05:37 PM
Replies: 67
Views: 2,403
Posted By jerrypoller
OK guys, I have to start this post by saying I...

OK guys, I have to start this post by saying I have absolutely no financial interest in this target company - none whatsoever. Here's the story. I was looking on line to replenish my dwindling...
Forum: CZ / Brno 04-03-2014, 02:47 PM
Replies: 67
Views: 2,403
Posted By jerrypoller
I've been shooting for some time, but it's never...

I've been shooting for some time, but it's never too late to learn something (or a lot of somethings). So, what does it mean to shoot a "clean" target. I'm embarrassed to ask, but not enough to...
Forum: CZ / Brno 04-02-2014, 05:09 PM
Replies: 357
Views: 112,218
Posted By jerrypoller
CZ452 UL with BRNO peeps at 100yds. indoors from...

CZ452 UL with BRNO peeps at 100yds. indoors from a bench with EleyStandard .22lrhttp://i124.photobucket.com/albums/p13/jerrypoller/100ydcz452_zps70b1ec89.jpg
Forum: CZ / Brno 04-02-2014, 02:36 PM
Replies: 67
Views: 2,403
Posted By jerrypoller
Good advice, both you and Glen. Got out my pipe...

Good advice, both you and Glen. Got out my pipe wrench today and "moved" the sight over a bit then shot this group:
http://i124.photobucket.com/albums/p13/jerrypoller/100ydcz452_zps70b1ec89.jpg
...
Forum: CZ / Brno 04-02-2014, 02:30 PM
Replies: 52
Views: 2,878
Posted By jerrypoller
Obsolutely - off a bench, indoors. If I could...

Obsolutely - off a bench, indoors. If I could shoot this offhand I'd like to think I could make a living from it :D
Forum: CZ / Brno 04-02-2014, 01:43 PM
Replies: 52
Views: 2,878
Posted By jerrypoller
I don't believe I'll ever shoot better

than this target. I now have my UL all set up and went to the range to see how I could do. Well, when I checked my spotting scope, I was sure I just couldn't see all the holes from 100 yds - I was...
Forum: Anschutz 03-30-2014, 06:17 PM
Replies: 40
Views: 2,874
Posted By jerrypoller
If I used brake cleaner and then "hosed" down the...

If I used brake cleaner and then "hosed" down the trigger group with lighter fluid a couple of times. will the rust issue be negated, or once it's in the mechanism it's there for good unless taken...
Forum: CZ / Brno 03-29-2014, 10:54 AM
Replies: 67
Views: 2,403
Posted By jerrypoller
Glen: I looked at the front globe yesterday,...

Glen:

I looked at the front globe yesterday, thinking I could adjust it for windage, but it looked to me like it could only be adjusted for elevation by moving it in the factory sight ramp front...
Forum: Model 597 03-29-2014, 10:40 AM
Replies: 10
Views: 1,350
Posted By jerrypoller
A good question - i hadn't measured the mag...

A good question - i hadn't measured the mag itself. So, I just checked all three and from the top of the mag to the [outside] base of the installed floor plate came out at .2264" for each. So, if...
Forum: Model 597 03-29-2014, 09:21 AM
Replies: 10
Views: 1,350
Posted By jerrypoller
So, first I measured the height of the follower...

So, first I measured the height of the follower in the mag I got with the rifle - it was able to take 10 rounds right from the beginning. It came in at .533". Then I started sanding down one of the...
Forum: CZ / Brno 03-29-2014, 06:24 AM
Replies: 67
Views: 2,403
Posted By jerrypoller
Thanks Glen. I put a square on the front of the...

Thanks Glen. I put a square on the front of the rail attachment and then tried to visually gauge how much "off square" to try and move the end of the sight attachment bar. It was hard to see if I...
Forum: CZ / Brno 03-28-2014, 06:56 PM
Replies: 67
Views: 2,403
Posted By jerrypoller
Glen: Not sure I follow your correction. ...

Glen:

Not sure I follow your correction. I'm not "seeing" it in my mind. Here's a picture of my BRNO. Can I impose on you one more time to try and walk me through which part needs the bend:...
Forum: Model 597 03-28-2014, 06:47 PM
Replies: 10
Views: 1,350
Posted By jerrypoller
Just read your post and had the same thought as I...

Just read your post and had the same thought as I just took my mags apart again. I noticed that the springs were easily compressed far enough to allow the follower to lower to the point of accepting...
Forum: Model 597 03-28-2014, 04:15 PM
Replies: 10
Views: 1,350
Posted By jerrypoller
597 mags only fit for 8 or 9 rounds

I just got two new factory (Rem 597 with the circle 10) magazines and they will only take 8 and 9 rounds respectively. I've pushed so hard I put a small dent from the rim in the last round to fit. ...
Forum: CZ / Brno 03-28-2014, 03:52 PM
Replies: 67
Views: 2,403
Posted By jerrypoller
Well, it seems I see better with the clear...

Well, it seems I see better with the clear inserts than with the metal set I got from Denny. So, an order just went out today for the clear "variety pack".

But I've also noticed that I have the...
Forum: CZ / Brno 03-21-2014, 06:17 PM
Replies: 52
Views: 2,878
Posted By jerrypoller
I have the BRNO sights (rear adjustable peep and...

I have the BRNO sights (rear adjustable peep and front globe) on my CZ 452 Ultra Lux. The BRNO sights were about $120 from Denny, the Anschutz adjustable aperture was $75 from Champion's Choice, and...
Forum: CZ / Brno 03-21-2014, 06:01 PM
Replies: 52
Views: 2,878
Posted By jerrypoller
Well, I got the Anschutz aperture and my YoDave...

Well, I got the Anschutz aperture and my YoDave spring kit today and installed them both. I used the slimmest shim and the second to lightest spring and now the trigger breaks crisply at a hair over...
Forum: Model 37/40X 03-21-2014, 02:18 PM
Replies: 275
Views: 45,576
Posted By jerrypoller
Thanks for the history Myles. I've often...

Thanks for the history Myles. I've often wondered how many hands my 37 has passed through on its way to me. It was obviously well cared for along the way. :o
Forum: Model 37/40X 03-21-2014, 06:37 AM
Replies: 275
Views: 45,576
Posted By jerrypoller
i read the PG codes the same way, but I've twice...

i read the PG codes the same way, but I've twice now gotten Remington to confirm my serial number corresponds to a 1940 build. Do you know if they just estimate the date based on a rough serial...
Forum: Model 37/40X 03-20-2014, 06:48 PM
Replies: 275
Views: 45,576
Posted By jerrypoller
Better late than never. My 37 (which Remington...

Better late than never. My 37 (which Remington tells me was built in 1940, based on the serial number) is number 02201 and has, what appear to be 3 Maltese Crosses stamped on the barrel just before...
Showing results 1 to 25 of 99

 


All times are GMT -5. The time now is 11:52 PM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x