RimfireCentral.com Forums - Search Results

Go Back   RimfireCentral.com Forums >

Notices

Join Team RFC to remove these ads.
Showing results 1 to 9 of 9
Search took 0.00 seconds.
Search: Posts Made By: Sav22
Forum: Mossberg 09-25-2019, 06:31 PM
Replies: 46
Views: 2,415
Posted By Sav22
Tang sights often have to be shimmed on one side...

Tang sights often have to be shimmed on one side of the base or the other, most rifles had the final polishing done by hand so the surface of the tangs can vary and not always be level to the...
Forum: Mossberg 09-25-2019, 09:37 AM
Replies: 46
Views: 2,415
Posted By Sav22
The Lyman tang sights were made into the 1950's,...

The Lyman tang sights were made into the 1950's, 'Old Gun Sights' say's the No 2's were discontinued in 1955 and I assume the No 1's would have been the same , or close.

From a 1950 Lyman catalog...
Forum: Mossberg 07-16-2019, 11:47 AM
Replies: 46
Views: 2,415
Posted By Sav22
You have to remove at least one of the extractors...

You have to remove at least one of the extractors to be able to remove the firing pin, there is a sleeve that holds the extractor spring going through a slot in the firing pin, it can be removed from...
Forum: Mossberg 07-04-2019, 08:20 AM
Replies: 46
Views: 2,415
Posted By Sav22
Bill, have you checked the stock number on the...

Bill, have you checked the stock number on the second gun? I am again surprised to see another straight grip stock on an M.


It looks to me that you will be able to complete one of them, I see...
Forum: Mossberg 06-29-2019, 09:47 PM
Replies: 46
Views: 2,415
Posted By Sav22
Bill, I now have three Model S's - one left...

Bill,

I now have three Model S's - one left blank after 'MODEL' in the barrel stamp and the other two used a broken stamp where the connection between the top & bottom curve of the 'S' is broken...
Forum: Mossberg 06-28-2019, 08:03 AM
Replies: 46
Views: 2,415
Posted By Sav22
Bill, if you weren't in Canada I might have been...

Bill, if you weren't in Canada I might have been able to help with some parts, I think there are a lot of restrictions on shipping any gun parts out of the USA now. I bought out a couple large groups...
Forum: Mossberg 04-12-2018, 07:01 PM
Replies: 46
Views: 2,415
Posted By Sav22
The crack looks tight so if the receiver halves...

The crack looks tight so if the receiver halves line up fairly close I wouldn't worry about that, it probably will feel a little loose, these seem to have a tendency to fit together with a little bit...
Forum: Mossberg 04-10-2018, 06:43 PM
Replies: 46
Views: 2,415
Posted By Sav22
some pictures - ...

some pictures -

https://www.24hourcampfire.com/ubbthreads/gallery/80/full/69972.jpg

https://www.24hourcampfire.com/ubbthreads/gallery/80/full/69973.jpg
...
Forum: Mossberg 04-10-2018, 05:15 PM
Replies: 46
Views: 2,415
Posted By Sav22
Looking at your pictures your gun has the later...

Looking at your pictures your gun has the later design changes - it has the later action release and the ball bearing cartridge stop which takes the later bolt design without two prongs on the front,...
Showing results 1 to 9 of 9

 


All times are GMT -5. The time now is 02:03 PM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x