RimfireCentral.com Forums - Search Results

Go Back   RimfireCentral.com Forums >

Notices

Join Team RFC to remove these ads.
Showing results 1 to 25 of 148
Search took 0.02 seconds.
Search: Posts Made By: 22/silencer
Forum: .17HM2 02-21-2020, 01:24 PM
Replies: 15
Views: 608
Posted By 22/silencer
I like this picture. it shows that if the bolt...

I like this picture. it shows that if the bolt is back as little as a 1/16 of inch the hammer will not come in contact with the firing pin. if it can you have out of spec parts, radius bolt, a...
Forum: .17HM2 01-27-2020, 01:08 PM
Replies: 127
Views: 10,299
Posted By 22/silencer
Also lf it is ok with Mike. I might be able to...

Also lf it is ok with Mike. I might be able to machine it ,only
After I get it. I could ship my 17hm2 bolt for you to use while
I have your bolt it might take a week or too .long work hour this...
Forum: .17HM2 01-27-2020, 12:57 PM
Replies: 127
Views: 10,299
Posted By 22/silencer
I may have gotten the bolt with the tungsten...

I may have gotten the bolt with the tungsten insert that sat up a little higher. Thickness of the bolt at the rear is .778 instead of .75. Anybody know how to grind tungsten down? My Dremel isnít...
Forum: .17HM2 01-10-2020, 04:40 PM
Replies: 127
Views: 10,299
Posted By 22/silencer
The bolts look grate. I never thought about edm.

The bolts look grate. I never thought about edm.
Forum: 10/22 Action 11-30-2019, 05:49 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
the pin is 8 gr same as the stock one. i only...

the pin is 8 gr same as the stock one.
i only had one 3/32 end mill with to short a length of cut so it cut a little
on the top of bolt in the slot will need to a longer one . also had to trim the...
Forum: 10/22 Action 11-28-2019, 05:04 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
i am not the best at silver soldering ,but it is...

i am not the best at silver soldering ,but it is a firing pin now.
now all i have to do trim to size, then finish the bolt then test.

Greg
Forum: 10/22 Action 11-26-2019, 01:28 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
That is what I was going to do, after I cut the ...

That is what I was going to do, after I cut the
Pin to lenght. Then fit the pin to the bolt.


Greg
Forum: 10/22 Action 11-25-2019, 08:57 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
well i am almost done with firing pin

well i am almost done with firing pin
Forum: 10/22 Action 11-19-2019, 04:00 AM
Replies: 120
Views: 7,680
Posted By 22/silencer
It will have two points on it.i 12 and 6 . will...

It will have two points on it.i 12 and 6 . will have to fit it to the bolt.
And yes the center will machine down.
Forum: 10/22 Action 11-18-2019, 10:25 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
this is what i was thinking

this is what i was thinking
Forum: 10/22 Action 11-16-2019, 04:21 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
has anyone had the time to get a firing pin made...

has anyone had the time to get a firing pin made up yet?
i have been thinking about the idea of taking two stock pin and
connecting them together, to test
Forum: 10/22 Action 10-28-2019, 02:27 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
No dremel, key way cutter.

No dremel, key way cutter.
Forum: 10/22 Action 10-28-2019, 01:35 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
I could try it on a 17hm2 to see if it would ...

I could try it on a 17hm2 to see if it would
Over pressure the base of the rim and dent.

Thanks Greg
Forum: 10/22 Action 10-28-2019, 01:33 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
I like the idea of 12 and 6 fireing pin hits ...

I like the idea of 12 and 6 fireing pin hits
Would you mind if I try your idea . Or do
You plan to do a service on this?

Thanks Greg
Forum: 10/22 Action 10-28-2019, 12:00 PM
Replies: 120
Views: 7,680
Posted By 22/silencer
A lot of open bolt 22 from the 50s and 60s Had...

A lot of open bolt 22 from the 50s and 60s
Had two pins machine in to the bolt for that same
Reason. Are you past the concepts stage, and
Do you have a working prototype to test?

Thanks Greg
Forum: FrankenRugers 08-22-2019, 05:51 PM
Replies: 9
Views: 645
Posted By 22/silencer
i have a mk2.

i have a mk2.
Forum: FrankenRugers 08-21-2019, 06:12 PM
Replies: 9
Views: 645
Posted By 22/silencer
about what year did you by yours, i got mine in...

about what year did you by yours, i got mine in 1993 and my bolt
look different but the magazine looks the same. i will try take a picture
of mine and post it here.

Greg
Forum: .17HM2 08-14-2019, 11:07 AM
Replies: 131
Views: 18,762
Posted By 22/silencer
Does it use the same bolt and locking as the...

Does it use the same bolt and locking as the a17hmr
Also what is the weight of the bolt,

Thanks Greg
Forum: FrankenRugers 08-12-2019, 10:30 PM
Replies: 9
Views: 645
Posted By 22/silencer
i have one in my suppressed mk11. run just as...

i have one in my suppressed mk11. run just as good as the shorts allow.

Greg
Forum: .17HM2 07-29-2019, 09:26 AM
Replies: 127
Views: 10,299
Posted By 22/silencer
What barrel length are you at? If longer than...

What barrel length are you at? If longer than 18in
You can tune it by shorting it a little at a time maybe.
Just thinking out loud


Greg
Forum: Mark II 06-25-2019, 11:32 PM
Replies: 13
Views: 1,079
Posted By 22/silencer
I got mine in the 90s from clark along with the...

I got mine in the 90s from clark along with the grips to change the angle to mach
the 45.
Forum: .17HM2 04-30-2019, 10:58 AM
Replies: 127
Views: 10,299
Posted By 22/silencer
I think the bolt bounce is from the stock springs...

I think the bolt bounce is from the stock springs and added weight.
Not enough spring pressure to keep bolt all the way closed.
I think that the ps heavy handle has a plus 10% spring but I could...
Forum: .17HM2 04-29-2019, 12:44 PM
Replies: 127
Views: 10,299
Posted By 22/silencer
Will you be testing with stronger hammer,...

Will you be testing with stronger hammer, charging springs?
Forum: .17HM2 04-16-2019, 06:34 PM
Replies: 127
Views: 10,299
Posted By 22/silencer
I have a Magnum Research 22 mag that I haven't...

I have a Magnum Research 22 mag that I haven't shot yet. It occurred to me that the hangup with a home-brew gun would be the bullet length. We'd need longer receivers. That would be the hurdle for a...
Forum: .17HM2 04-16-2019, 12:25 PM
Replies: 127
Views: 10,299
Posted By 22/silencer
I've also been thinking about 22 magnums. Has...

I've also been thinking about 22 magnums. Has anyone used a weighted bolt and springs with a steel receiver to build a 22WMR in a regular 10/22-sized receiver?[/QUOTE]


What host are you using...
Showing results 1 to 25 of 148

 


All times are GMT -5. The time now is 03:45 AM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©2000-2018 RimfireCentral.com
x