RimfireCentral.com Forums - Search Results

Go Back   RimfireCentral.com Forums >

Notices

Join Team RFC to remove these ads.
Showing results 1 to 16 of 16
Search took 0.01 seconds.
Search: Posts Made By: WildMike
Forum: 10/22 Barrels - Factory & Aftermarket 08-30-2019, 02:33 PM
Replies: 2
Views: 749
Posted By WildMike
My sport tapered Fedderson will shoot 1/2" at 50...

My sport tapered Fedderson will shoot 1/2" at 50 yards with SK standard plus
Forum: 10/22 Barrels - Factory & Aftermarket 04-09-2019, 06:45 PM
Replies: 11
Views: 1,850
Posted By WildMike
Feddersen will back his guarantee. I replaces all...

Feddersen will back his guarantee. I replaces all my GM barrels with Feddersen.
Forum: Ultimate 10/22 02-14-2019, 01:35 PM
Replies: 2
Views: 595
Posted By WildMike
my build

Birch stock modified with cherry. Mesa receiver Fedderison barrel
Forum: Ruger - Other 02-11-2019, 11:47 AM
Replies: 6
Views: 880
Posted By WildMike
I put a Shaw barrel on My RPR also. as well as a...

I put a Shaw barrel on My RPR also. as well as a foil tape bedding for the block. Has already seen some improvements.
Forum: Ruger - Other 11-13-2018, 08:52 AM
Replies: 42
Views: 7,440
Posted By WildMike
BSA Platinum 36x44 on my RPR, but I mite change...

BSA Platinum 36x44 on my RPR, but I mite change that to a BAS platinum 8-32x44 milldot
Forum: 10/22 Barrels - Factory & Aftermarket 10-19-2018, 11:50 AM
Replies: 6
Views: 1,393
Posted By WildMike
keep a little oil on your compensator and use a...

keep a little oil on your compensator and use a worn bore snake every time you shoot. Then a q-tip for a light pass on the comp. My guns don't like to be completely clean but the comps will build up...
Forum: Henry 04-24-2017, 01:30 AM
Replies: 737
Views: 319,815
Posted By WildMike
http://<a...

http://<a href="http://s177.photobucket.com/user/bikermikearchery/media/P3250002_zpsmcojqr7l.jpg.html" target="_blank"><img...
Forum: Appleseed 03-30-2017, 03:41 PM
Replies: 16
Views: 1,290
Posted By WildMike
Its not such a bad question. I have been thinking...

Its not such a bad question. I have been thinking of the same thing. my thoughts.
1...I'd use a tapered or OME barrel. The little bit of weight you save helps in the offhand. I have been bench...
Forum: Henry 03-25-2017, 02:26 AM
Replies: 5
Views: 741
Posted By WildMike
I am looking at some of the receiver sights. I...

I am looking at some of the receiver sights. I also have looked in my old books and seen a fix using 2 copper rods in the dovetail. that and a set screw in the sight mite work.
Forum: Henry 03-24-2017, 05:58 PM
Replies: 5
Views: 741
Posted By WildMike
Hennry's rear dove tail 7/16 ?

Hello all.
I got a rear bullseye sight that had the standard 3/8 dovetail.
Drifted out the original sight and was surprised to find the dove tail on the barrel is 7/16.
I did a quick look and...
Forum: 10/22 Action 03-20-2017, 12:24 PM
Replies: 18
Views: 1,203
Posted By WildMike
I bought a used 10 22 that had 2 of the holes...

I bought a used 10 22 that had 2 of the holes already oversized tapped. One more of the holes was just about gone. I replaced the Scope rail with a 15MOA Piccatinny cleaned the buggered screw hole...
Forum: Single Six 03-16-2017, 06:37 PM
Replies: 10
Views: 2,999
Posted By WildMike
I found long ago that polishing the cylinder...

I found long ago that polishing the cylinder chambers makes life better with most revolvers. I use a 3/16 brass rod wrapped in cotton thread and Jewelers rouge.. Chucked in a cordless I run a few...
Forum: Ruger - Other 03-16-2017, 02:29 PM
Replies: 9
Views: 1,865
Posted By WildMike
Sad accuracy from Ruger's 22lr revolvers

With over 20 Rugers in my safe I am just so disappointed with the Accuracy of Ruger's 22lr. Revolvers. I can make Silver dollar sized groups at 20 yds with my GP100, Blackhawk and Vaquero in 357...
Forum: 10/22 Action 03-16-2017, 02:05 PM
Replies: 21
Views: 2,125
Posted By WildMike
just throwing my 2 cents in. I built a 10 22...

just throwing my 2 cents in.
I built a 10 22 from a receiver only. The receiver cost $80.00 plus 20 for shipping and 20 fro transfer. $120.00 total. Could have bought a complete 10 22 for 200.......
Forum: 10/22 Barrels - Factory & Aftermarket 03-15-2017, 03:00 AM
Replies: 7
Views: 1,039
Posted By WildMike
that's what I was looking for. Thanks

that's what I was looking for. Thanks
Forum: 10/22 Barrels - Factory & Aftermarket 03-14-2017, 02:50 PM
Replies: 7
Views: 1,039
Posted By WildMike
cut re-crown and rechamber

Looking for recommendations for someone that will cut, thread, re-crown , and re-chamber OEM Ruger barrels.
Showing results 1 to 16 of 16

 


All times are GMT -5. The time now is 06:13 AM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x