RimfireCentral.com Forums - Search Results

Go Back   RimfireCentral.com Forums >

Join Team RFC to remove these ads.
Showing results 1 to 25 of 222
Search took 0.02 seconds.
Search: Posts Made By: boomer47
Forum: Marlin Semiautomatic 05-06-2020, 04:31 PM
Replies: 10
Views: 849
Posted By boomer47
I shoot stinger and velocitors all the time in my...

I shoot stinger and velocitors all the time in my '60 with the stock spring.

Velocitor cases are the same length as the .22lr, stingers are a tad longer and may not fully seat in SOME chambers. I...
Forum: Mk IV 04-27-2020, 07:54 AM
Replies: 11
Views: 654
Posted By boomer47
You can also spread the last coil on the end of...

You can also spread the last coil on the end of the spring that goes in the safety hole just enough to make a good tight fit in the hole and stop the whole thing from flying out again.
Forum: Mk IV 04-15-2020, 08:27 PM
Replies: 7
Views: 964
Posted By boomer47
I just finished looking the bolt over and...

I just finished looking the bolt over and checking the firing pin. It is one of the old style with only one hole but it is too rough to be a VQ pin. Polished it up a bit and will see how it does.

...
Forum: Mk IV 04-15-2020, 04:13 PM
Replies: 7
Views: 964
Posted By boomer47
New MK1V bolt

Bought a MK1V upper the other day from Volquartsen then saw an ad for a new complete MK1V bolt on e-bay for $35.00.


Fast shipping and is as advertised.


https://www.ebay.com/itm/223956885955
Forum: Marlin Semiautomatic 05-31-2019, 05:05 PM
Replies: 39
Views: 6,493
Posted By boomer47
Sad,sad news. I have one I would never part with...

Sad,sad news. I have one I would never part with and wish I had bought a few more when available .
No idea why Arrowdoger is not making the trigger any more but I doubt there will ever be a better...
Forum: Marlin Semiautomatic 05-23-2019, 08:37 AM
Replies: 17
Views: 2,442
Posted By boomer47
Hornady One Shot. Here is why. ...

Hornady One Shot.


Here is why.




http://ronkulas.proboards.com/thread/274/review-comparison-gun-care-products
Forum: Mk IV 11-18-2018, 08:12 AM
Replies: 12
Views: 2,164
Posted By boomer47
Well, my solution is: Use a small needle nose and...

Well, my solution is: Use a small needle nose and spread the last coil on one end of the spring to make a tight fit in the hole in the safety. Crimp the last coil on the other end to make tight grip...
Forum: Mk IV 11-01-2018, 08:34 AM
Replies: 47
Views: 5,909
Posted By boomer47
Here is a link to the best lube tests I have...

Here is a link to the best lube tests I have seen.
I've been using the Hornady One Shot for a couple of years now and really like the dry lube type on bolts and rails.
I get less powder residue...
Forum: Marlin Semiautomatic 10-18-2018, 08:16 AM
Replies: 10
Views: 1,745
Posted By boomer47
Don't waste time and money trying other fixes....

Don't waste time and money trying other fixes. Get the KAT trigger and you will have the best you can get.
Forum: Mk IV 07-21-2018, 08:12 AM
Replies: 40
Views: 4,974
Posted By boomer47
Rimfire sports now has the grips for the...

Rimfire sports now has the grips for the standard. Not on his web site yet but I just ordered over the phone.
Forum: Mk IV 06-21-2018, 04:07 PM
Replies: 5
Views: 547
Posted By boomer47
TM, assuming you have the VQ trigger. What size...

TM, assuming you have the VQ trigger. What size screws did you order from McMaster?
Forum: Marlin Semiautomatic 06-07-2018, 01:12 PM
Replies: 194
Views: 46,902
Posted By boomer47
Arrow dodger put a KAT in my '60 about a year or...

Arrow dodger put a KAT in my '60 about a year or so ago.
I have been a gun nut for around 65 years and have tweaked and had tweaked many semi pistols revolvers, shotguns and rifles.
The KAT setup...
Forum: Mk IV 04-11-2018, 07:29 AM
Replies: 48
Views: 9,354
Posted By boomer47
I did mention the MK111 pin but did not make it...

I did mention the MK111 pin but did not make it clear that I was modifying a MK111 pin. I didn't like the looks of that mk1V pin from the gitgo.
Forum: Mk IV 04-10-2018, 03:27 PM
Replies: 48
Views: 9,354
Posted By boomer47
Here is my solution to light strikes with the...

Here is my solution to light strikes with the factory original MK1V firing pin.
I squared off the tip and took off a tad in the rear of the hole in the MK111 firing pin so as to keep the same amount...
Forum: Marlin Semiautomatic 03-29-2018, 11:45 AM
Replies: 21
Views: 12,914
Posted By boomer47
The KAT trigger is the best upgrade you will ever...

The KAT trigger is the best upgrade you will ever make.
Forum: Mk IV 03-08-2018, 09:56 AM
Replies: 40
Views: 4,974
Posted By boomer47
I called Hogue a few minutes ago and was told...

I called Hogue a few minutes ago and was told that the rubber wraparounds will not be available til mid May.
I was told back in December the grips would come out in Jan.
Forum: Mk IV 02-18-2018, 09:48 AM
Replies: 10
Views: 1,695
Posted By boomer47
When you get the new one take a small needle nose...

When you get the new one take a small needle nose and crimp the last coil of the spring enough to make a real tight fit on the shaft of the plunger then spread the last coil on the other end of the...
Forum: Mk IV 12-14-2017, 08:41 AM
Replies: 40
Views: 4,974
Posted By boomer47
I called Hogue yesterday and they now say MAYBE...

I called Hogue yesterday and they now say MAYBE feb. or march.
Forum: Marlin Semiautomatic 11-21-2017, 07:52 AM
Replies: 3
Views: 699
Posted By boomer47
Not completely tactical but I have one on my 60...

Not completely tactical but I have one on my 60 and really like it.

https://www.atioutdoors.com/fiberforce-marlin-stock
Forum: 22/45 Mark IV 11-13-2017, 06:12 PM
Replies: 41
Views: 4,275
Posted By boomer47
The cylindrical steel-coloured part is the recoil...

The cylindrical steel-coloured part is the recoil spring guide rod.
OP, check the clearance between the rear lips of the mag and the ejector, should be 1/16th or so. Mag sitting too low will cause...
Forum: Mk IV 10-17-2017, 05:19 PM
Replies: 7
SGW
Views: 2,128
Posted By boomer47
Yeah, I knew my first post had been deleted but...

Yeah, I knew my first post had been deleted but don't know why.
Anyway, I guess I'll leave well enough alone. I'll miss him.
Forum: Mk IV 10-17-2017, 03:59 PM
Replies: 7
SGW
Views: 2,128
Posted By boomer47
SGW

I asked once before about why we don't see posts by SGW anymore and only got a reply that said he had "departed this forum"
What does that mean? died, banned from the forum, just got mad and quit,...
Forum: Mk IV 10-02-2017, 11:34 AM
Replies: 3
Views: 687
Posted By boomer47
Lug Retainer Screw and Firing Pin

I just called Ruger about getting a new "bumper". The rep seemed to be in the dark and said she was not aware of any problems with the part but would send me one anyway.
I also asked about the...
Forum: Mark III 08-26-2017, 11:59 AM
Replies: 8
Views: 1,378
Posted By boomer47
How do you measure your"lock time" to determine...

How do you measure your"lock time" to determine which is faster?
Forum: Mk IV 08-26-2017, 09:51 AM
Replies: 184
Views: 13,453
Posted By boomer47
I've been looking at the safety operation on my...

I've been looking at the safety operation on my post recall MK1V.
I can still finagle the safety to just before the full on and off and get the hammer to fall.
Watching the safety/sear engagement...
Showing results 1 to 25 of 222

 


All times are GMT -5. The time now is 03:41 PM.

Privacy Policy

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com
x