RimfireCentral.com Forums

RimfireCentral.com Forums (https://www.rimfirecentral.com/forums/index.php)
-   10/22 Stocks - Factory & Aftermarket (https://www.rimfirecentral.com/forums/forumdisplay.php?f=155)
-   -   The Titan Spike is here finally! (https://www.rimfirecentral.com/forums/showthread.php?t=1165359)

Michael Victor 07-01-2019 04:06 PM

The Titan Spike is here finally!
 
Hello Gents,

We have just released our latest upgrade for our Titan 1022 Stock... the Titan Spike Anchor.

This simple device gives your Titan stock a second point of engagement to increase consistency and accuracy. It's very easy to install and with the supplied tools, you will be able to tune it for the best performance for your action.

The Spike actually presses down against the rear of the 10/22 receiver and holds it in place. You will need to play around with how much pressure to put on it but we have found 8-15 inch pounds works well.

One thing to keep in mind is the Spike is a SPIKE, so it will mark the back of your receiver. If you do not want a mark on the back of your receiver then don't use the SPIKE : )

If you receiver has a cleaning rod hole, the Spike will fit without a problem.

Here are some pics- let me know if you have questions or thoughts. I'm here to help!

Best,

Michael V.

(Btw- you can purchase it here: www.victorcompanyusa.com)


https://i.imgur.com/F55bVPc.jpg



https://i.imgur.com/ugm2Cno.jpg



https://i.imgur.com/MqjvsbE.jpg



https://i.imgur.com/pl8VOJh.jpg

nodak 07-01-2019 06:28 PM

Would love to see a pic of where is marks the receiver at.

crackedcornish 07-01-2019 08:19 PM

Quote:

Originally Posted by nodak (Post 11530975)
Would love to see a pic of where is marks the receiver at.

yes, me too

Michael Victor 07-01-2019 10:12 PM

Quote:

Originally Posted by nodak (Post 11530975)
Would love to see a pic of where is marks the receiver at.

Good request- here is a pic of a Tac Sol X-Ring Receiver with a Spike mark...

https://i.imgur.com/XW1TY2M.jpg

NicholsT55 07-01-2019 10:49 PM

That's not bad looking, and it'll be hidden (under the woodline) even if you later decide to remove the Spike. It's looks like a good alternative to having to modify your receiver for another manufacturer's solution to the same problem.

Mr_Lee 07-02-2019 11:14 PM

Would the Spike with with aftermarket receivers too? I have a Feddersen Aluminum receiver.

Rick67 07-02-2019 11:28 PM

Quote:

Originally Posted by Mr_Lee (Post 11532043)
Would the Spike with with aftermarket receivers too? I have a Feddersen Aluminum receiver.

I think it would.

I have a Fed receiver too, and HAD a Titan stock once and they fit fine.

FLATHEAD1936 07-06-2019 10:07 PM

Titan Spike
 
Just received the Spike today (quick delivery I must say) and just installed in the Titan stock quick and easy on a Volquartsen Summit receiver. I don't care about a mark I can't see and no one else can either.

Treefeller22 07-08-2019 02:29 AM

Quote:

Originally Posted by FLATHEAD1936 (Post 11536143)
Just received the Spike today (quick delivery I must say) and just installed in the Titan stock quick and easy on a Volquartsen Summit receiver. I don't care about a mark I can't see and no one else can either.

How well does it fit? Where does it mark?

Rick67 07-08-2019 02:49 AM

Can you not see the photo posted by Mr. Victor himself?

wolfshoon 07-08-2019 02:57 AM

So you are not worried about stress fractures/cracking originating out of the gouge the Spike puts in the back of the receiver? That is pretty close edge distance to the bottom.

Treefeller22 07-08-2019 08:12 AM

Quote:

Originally Posted by Rick67 (Post 11537401)
Can you not see the photo posted by Mr. Victor himself?

i was referring to the Volquartsen Summit, not a 10/22 as shown.

Michael Victor 07-08-2019 03:55 PM

Quote:

Originally Posted by wolfshoon (Post 11537403)
So you are not worried about stress fractures/cracking originating out of the gouge the Spike puts in the back of the receiver? That is pretty close edge distance to the bottom.

In the year of shooting/testing we haven't had any issues.

NicholsT55 07-08-2019 05:26 PM

I wouldn't think that it would hurt a thing, even if the receiver did crack in that location. It's not like that's a high-stress area, subject to hammering from the bolt or anything. If I had one and the receiver cracked there, I think I'd reinforce it with some JB Weld and continue shooting.

Ionian 07-18-2019 04:01 PM

How about some OD green stocks already!😜


All times are GMT -5. The time now is 04:22 AM.

DMCA Notice

Powered by vBulletin
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimisation provided by DragonByte SEO (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright 2000-2018 RimfireCentral.com